# 1 generation to current help

**URL:** <https://forums.maslowcnc.com/t/1-generation-to-current-help/21594>\
**Category:** No Judgement\
**Created:** [June 20, 2024, 9:53pm UTC](https://forums.maslowcnc.com/t/1-generation-to-current-help/21594 "2024-06-20T21:53:22Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![Zachariah\_Collom](https://avatars.discourse-cdn.com/v4/letter/z/d9b06d/32.png) [@Zachariah\_Collom](https://forums.maslowcnc.com/u/Zachariah_Collom)\
**Post date:** [June 20, 2024, 9:53pm UTC](https://forums.maslowcnc.com/t/1-generation-to-current-help/21594/1 "2024-06-20T21:53:22Z")

</div>

I purchased a Kickstarter version of the Maslow. I used to use it. I moved 5 years ago and it had to go into storage. I pulled it back out and the computer I was using was toast as is the Arduino. I think that the CNC board is still good.

Can I download the latest firmware and install on a new arduino and use it without modification to my frame. I see the latest version is built differently.

Thank you,  
Zachariah

---

<div class="post-metadata">

**Author:** ![TimS](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/tims/32/17329_2.png) [@TimS](https://forums.maslowcnc.com/u/TimS)\
**Post date:** [June 20, 2024, 10:04pm UTC](https://forums.maslowcnc.com/t/1-generation-to-current-help/21594/2 "2024-06-20T22:04:14Z")

</div>

Webcontrol v0.94 has a firmware installer as part of the program. Install holey firmware.

> [@Help! Maslow version 1, building. Can't find instructions](https://forums.maslowcnc.com/t/help-maslow-version-1-building-cant-find-instructions/21489/4):
>
> If you need help, I’ll be willing to talk you through on the phone.

---

<div class="post-metadata">

**Author:** ![DanG1](https://avatars.discourse-cdn.com/v4/letter/d/5daacb/32.png) [@DanG1](https://forums.maslowcnc.com/u/DanG1)\
**Post date:** [September 9, 2024, 5:09pm UTC](https://forums.maslowcnc.com/t/1-generation-to-current-help/21594/3 "2024-09-09T17:09:59Z")

</div>

So funny, I find myself in almost the exact same situation… Purchased an earlier version of Maslow years ago, moved (without ever using it in my case) and only just recently found it again still fresh in its original unopened box. I’d like to use it but I can’t seem to find the original info for it and I’m finding the wiki a little intimidating. Are there any links to the setup for the orginal Maslow still available?

---

<div class="post-metadata">

**Author:** ![bar](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/bar/32/10_2.png) [@bar](https://forums.maslowcnc.com/u/bar)\
**Post date:** [September 9, 2024, 6:36pm UTC](https://forums.maslowcnc.com/t/1-generation-to-current-help/21594/4 "2024-09-09T18:36:28Z")

</div>

You can find assembly instructions for it here: [Maslow Electronics](http://maslowcommunitygarden.org/Electronics.html?instructions=True)