# Calibration doesn’t work

**URL:** <https://forums.maslowcnc.com/t/calibration-doesn-t-work/24124>\
**Category:** Troubleshooting\
**Created:** [May 16, 2025, 2:52pm UTC](https://forums.maslowcnc.com/t/calibration-doesn-t-work/24124 "2025-05-16T14:52:40Z")\
**Posts on this page:** 16\
**Page:** 1

<div class="post-metadata">

**Author:** ![VinileC](https://avatars.discourse-cdn.com/v4/letter/v/58956e/32.png) [@VinileC](https://forums.maslowcnc.com/u/VinileC)\
**Post date:** [May 16, 2025, 2:52pm UTC](https://forums.maslowcnc.com/t/calibration-doesn-t-work/24124/1 "2025-05-16T14:52:40Z")

</div>

I’m not sure what I’m doing wrong. But Iv build a frame. Gone through the calibration process a couple times and nothing is working.

Says it’s ready to cut but can’t even get it to jog. Clicked home and it just unwound the belts.

Iv tried attaching a video of what it’s doing but won’t let me do anything over 8mb.

Just keeps restarting the fitness saying it’s to low.

Sam

---

<div class="post-metadata">

**Author:** ![bar](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/bar/32/10_2.png) [@bar](https://forums.maslowcnc.com/u/bar)\
**Post date:** [May 16, 2025, 3:07pm UTC](https://forums.maslowcnc.com/t/calibration-doesn-t-work/24124/2 "2025-05-16T15:07:49Z")

</div>

Can you try following along with this video and see where what you are seeing is different than what is in the video?

[![](https://img.youtube.com/vi/mQwz0omOKJc/maxresdefault.jpg "Maslow Calibration Walkthrough 1.05") ](https://www.youtube.com/watch?v=mQwz0omOKJc)

---

<div class="post-metadata">

**Author:** ![VinileC](https://avatars.discourse-cdn.com/v4/letter/v/58956e/32.png) [@VinileC](https://forums.maslowcnc.com/u/VinileC)\
**Post date:** [May 20, 2025, 2:44pm UTC](https://forums.maslowcnc.com/t/calibration-doesn-t-work/24124/3 "2025-05-20T14:44:04Z")

</div>

Iv tried following that about 10 times so far.

So frustrating. I’m uk based so this is taking forever to get sorted with the time difference. It’s better today but when I try and calibrate the bottom belts don’t go tense. They stay slack.

I still get the restarting fitness constant scrolling message in the code.

Just says calculated fitness to low. It’s a Maslow 4 and just upgraded the firmware. This is the first time using it since it arriving last August. Something isn’t right. !!!

Can you please help? I can’t see anything I’m doing wrong.

---

<div class="post-metadata">

**Author:** ![VinileC](https://avatars.discourse-cdn.com/v4/letter/v/58956e/32.png) [@VinileC](https://forums.maslowcnc.com/u/VinileC)\
**Post date:** [May 20, 2025, 2:52pm UTC](https://forums.maslowcnc.com/t/calibration-doesn-t-work/24124/4 "2025-05-20T14:52:36Z")

</div>

Iv got it set up vertically and the sled keeps falling off the bottom. This thing is seriously not right.

It does the frame flex. But only seems to do it once not twice then all the belts extend and crunch together. !!!

---

<div class="post-metadata">

**Author:** ![VinileC](https://avatars.discourse-cdn.com/v4/letter/v/58956e/32.png) [@VinileC](https://forums.maslowcnc.com/u/VinileC)\
**Post date:** [May 20, 2025, 2:54pm UTC](https://forums.maslowcnc.com/t/calibration-doesn-t-work/24124/5 "2025-05-20T14:54:32Z")

</div>

The bottom 2 belts are almost fully extending during calibration. It’s almost perfectly centre when I hang it on the frame. Then it runs calibration and completely goes off the ply.

---

<div class="post-metadata">

**Author:** ![VinileC](https://avatars.discourse-cdn.com/v4/letter/v/58956e/32.png) [@VinileC](https://forums.maslowcnc.com/u/VinileC)\
**Post date:** [May 20, 2025, 3:03pm UTC](https://forums.maslowcnc.com/t/calibration-doesn-t-work/24124/6 "2025-05-20T15:03:02Z")

</div>

All I keep doing is exactly what your video says but it’s not working!!!

---

<div class="post-metadata">

**Author:** ![bar](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/bar/32/10_2.png) [@bar](https://forums.maslowcnc.com/u/bar)\
**Post date:** [May 20, 2025, 6:17pm UTC](https://forums.maslowcnc.com/t/calibration-doesn-t-work/24124/7 "2025-05-20T18:17:26Z")

</div>

> [@VinileC](#):
>
> Iv got it set up vertically and the sled keeps falling off the bottom.

This sounds to me like the machine thinks that it’s in horizontal mode. It’s not expecting gravity to be pulling down on it like that which is why it goes off the bottom.

Can you double check the setting for horizontal vs vertical mode is correct?

---

<div class="post-metadata">

**Author:** ![ian\_ab](https://avatars.discourse-cdn.com/v4/letter/i/a587f6/32.png) [@ian\_ab](https://forums.maslowcnc.com/u/ian_ab)\
**Post date:** [May 20, 2025, 7:10pm UTC](https://forums.maslowcnc.com/t/calibration-doesn-t-work/24124/8 "2025-05-20T19:10:19Z")

</div>

> [@VinileC](#):
>
> Then it runs calibration and completely goes off the ply.

Also check the Maslow orientation, the power to the maslow board must be coming out in a down direction. I had a similar problem when I mounted mine vertically and had the power pointing up. I also have a 240V router..

---

<div class="post-metadata">

**Author:** ![VinileC](https://avatars.discourse-cdn.com/v4/letter/v/58956e/32.png) [@VinileC](https://forums.maslowcnc.com/u/VinileC)\
**Post date:** [May 20, 2025, 8:34pm UTC](https://forums.maslowcnc.com/t/calibration-doesn-t-work/24124/9 "2025-05-20T20:34:53Z")

</div>

I think this is it!! My wires are pointing upwards!

Il try it in the morning. Fingers crossed!

---

<div class="post-metadata">

**Author:** ![VinileC](https://avatars.discourse-cdn.com/v4/letter/v/58956e/32.png) [@VinileC](https://forums.maslowcnc.com/u/VinileC)\
**Post date:** [May 20, 2025, 8:35pm UTC](https://forums.maslowcnc.com/t/calibration-doesn-t-work/24124/10 "2025-05-20T20:35:27Z")

</div>

I did make sure a couple times it was vertical. I think Ian’s right with the board being upside down. Thinks the bed is upside down.

---

<div class="post-metadata">

**Author:** ![VinileC](https://avatars.discourse-cdn.com/v4/letter/v/58956e/32.png) [@VinileC](https://forums.maslowcnc.com/u/VinileC)\
**Post date:** [May 21, 2025, 8:34am UTC](https://forums.maslowcnc.com/t/calibration-doesn-t-work/24124/11 "2025-05-21T08:34:06Z")

</div>

so this looks to have sorted it not falling off the board. but i am still getting fitness to low scrolling messsage keeps restarting. any advice? @bar ?

---

<div class="post-metadata">

**Author:** ![VinileC](https://avatars.discourse-cdn.com/v4/letter/v/58956e/32.png) [@VinileC](https://forums.maslowcnc.com/u/VinileC)\
**Post date:** [May 21, 2025, 8:37am UTC](https://forums.maslowcnc.com/t/calibration-doesn-t-work/24124/12 "2025-05-21T08:37:16Z")

</div>

Serial Messages  
Index.html Version: 1.05  
[MSG:INFO: Channel auto report interval set to 50 ms]  
[MSG:INFO: FluidNC v3.0.x (noGit)]  
[MSG:INFO: Compiled with ESP32 SDK:v4.4.7-dirty]  
[MSG:INFO: Local filesystem type is littlefs]  
[MSG:INFO: Configuration file:maslow.yaml]  
[MSG:INFO: Machine Maslow S3 Board]  
[MSG:INFO: Board Maslow]  
[MSG:INFO: UART1 Tx:gpio.1 Rx:gpio.2 RTS:NO\_PIN Baud:115200]  
[MSG:INFO: SPI SCK:gpio.12 MOSI:gpio.11 MISO:gpio.13]  
[MSG:INFO: SD Card cs\_pin:gpio.10 detect:NO\_PIN freq:8000000]  
[MSG:INFO: Stepping:Timed Pulse:4us Dsbl Delay:0us Dir Delay:0us Idle Delay:240ms]  
[MSG:INFO: Axis count 3]  
[MSG:INFO: Axis X (-2438.400,0.000)]  
[MSG:INFO: Motor0]  
[MSG:INFO: Axis Y (-1219.200,0.000)]  
[MSG:INFO: Motor0]  
[MSG:INFO: Axis Z (-100.000,0.000)]  
[MSG:INFO: Motor0]  
[MSG:INFO: tmc\_2209 UART1 Addr:0 Step:gpio.15 Dir:gpio.16 Disable:NO\_PIN R:0.110]  
[MSG:INFO: Motor1]  
[MSG:INFO: tmc\_2209 UART1 Addr:1 Step:gpio.46 Dir:gpio.38 Disable:NO\_PIN R:0.110]  
[MSG:INFO: Z Axis driver test passed]  
[MSG:INFO: Z2 Axis driver test passed]  
[MSG:INFO: Kinematic system: Cartesian]  
[MSG:INFO: Using spindle NoSpindle]  
[MSG:INFO: Connecting to STA SSID:TP-Link\_HomeOffice]  
[MSG:INFO: Connecting.]  
[MSG:INFO: Connecting..]  
[MSG:INFO: Connected - IP is 192.168.1.107]  
[MSG:INFO: WiFi on]  
[MSG:INFO: Start mDNS with hostname:[http://maslow.local/](http://maslow.local/)]  
[MSG:INFO: SSDP Started]  
[MSG:INFO: HTTP started on port 80]  
[MSG:INFO: Telnet started on port 23]  
[MSG:INFO: Caution: Unlocked]  
Retract All  
[MSG:INFO: Retracting all belts]  
[MSG:INFO: Requesting state change from Unknown to Retracting Belts]  
[MSG:INFO: Succeeded]  
[MSG:INFO: Top Left pulled tight with offset -0.021]  
[MSG:INFO: Top Right pulled tight with offset -0.021]  
[MSG:INFO: Bottom Right pulled tight with offset -0.118]  
[MSG:INFO: Bottom Left pulled tight with offset -0.054]  
[MSG:INFO: Requesting state change from Retracting Belts to Belts Retracted]  
[MSG:INFO: Succeeded]  
Extend All  
[MSG:INFO: Extending all belts]  
[MSG:INFO: Requesting state change from Belts Retracted to Extending Belts]  
[MSG:INFO: Succeeded]  
[MSG:INFO: All belts extended to 1750.000mm]  
[MSG:INFO: Requesting state change from Extending Belts to Belts Extended]  
[MSG:INFO: Succeeded]  
Calibrate  
[MSG:INFO: Requesting state change from Belts Extended to Calibrating]  
[MSG:INFO: Setting z-stop position]  
[MSG:INFO: Machine Position found as X: -10.167 Y: 39.892]  
[MSG:INFO: Succeeded]  
[MSG:INFO: Measured waypoint 0]  
[MSG:INFO: Center point off by: TL: 0.000 TR: 0.000 BL: -44.523 BR: -73.298]  
[MSG:INFO: Machine Position computed as X: -8.377 Y: 54.531]  
[MSG:INFO: Measuring Frame Flex]  
[MSG:INFO: Flex measurement: TLBR: 3.025 TRBL: 4.126]  
[MSG:INFO: Measured waypoint 1]  
[MSG:INFO: Measured waypoint 2]  
[MSG:INFO: Measured waypoint 3]  
[MSG:INFO: Measured waypoint 4]  
[MSG:INFO: Measured waypoint 5]  
CLBM:[{bl:1904.15, br:1896.53, tr:1902.82, tl:1900.74},{bl:2006.70, br:1793.34, tr:1800.80, tl:2008.10},{bl:2109.22, br:1896.24, tr:1694.44, tl:1920.46},{bl:2012.59, br:1997.04, tr:1798.89, tl:1804.34},{bl:1910.60, br:2100.80, tr:1915.73, tl:1692.55},{bl:1796.32, br:2004.95, tr:2010.93, tl:1791.93},]  
Computing… This may take several minutes  
[MSG:INFO: Requesting state change from Calibrating to Ready To Cut]  
[MSG:INFO: Succeeded]Fitness: 0.0792421 in 100  
Fitness: 0.1010021 in 200  
Fitness: 0.1435367 in 300  
Fitness: 0.2483256 in 400  
Fitness: 0.3259596 in 500  
Fitness: 0.3385406 in 600  
Fitness: 0.3469373 in 700  
Fitness: 0.3532391 in 800  
Fitness: 0.3587685 in 900  
Fitness: 0.3645375 in 1000  
Fitness: 0.3709971 in 1100  
Fitness: 0.3762129 in 1200  
Fitness: 0.3816153 in 1300  
Fitness: 0.3889783 in 1400  
Fitness: 0.4011427 in 1500  
Fitness: 0.4182128 in 1600  
Fitness: 0.4435975 in 1700  
Fitness: 0.4539245 in 1800  
Fitness: 0.4552828 in 1900  
Fitness: 0.4555065 in 2000  
Fitness: 0.4557196 in 2100  
Fitness: 0.4559958 in 2200  
Fitness: 0.4564096 in 2300  
Fitness: 0.4568854 in 2400  
Fitness: 0.4576006 in 2500  
Fitness: 0.4584618 in 2600  
Fitness: 0.4595885 in 2700  
Fitness: 0.4611016 in 2800  
Fitness: 0.4631067 in 2900  
Fitness: 0.4654751 in 3000  
Fitness: 0.4687643 in 3100  
Fitness: 0.4698101 in 3200  
Fitness: 0.4698101 in 3300  
Fitness: 0.4698101 in 3400  
Fitness: 0.4698101 in 3500  
Fitness: 0.4698101 in 3600  
Fitness: 0.4698101 in 3700  
Fitness: 0.4698101 in 3800  
Fitness: 0.4698101 in 3900  
Fitness: 0.4698101 in 4000  
Fitness: 0.4698101 in 4100

Calculated Fitness Too Low. The process will automatically try again.!  
Calibration values:  
Fitness: 0.4698100750488708  
Maslow\_tlX: 22.1  
Maslow\_tlY: 2029.6  
Maslow\_trX: 3215.5  
Maslow\_trY: 2031.9  
Maslow\_blX: 0.0  
Maslow\_blY: 0.0  
Maslow\_brX: 3227.7  
Maslow\_brY: 0.0  
RestartingFitness: 0.4344721 in 100  
Fitness: 0.4528211 in 200  
Fitness: 0.4551070 in 300  
Fitness: 0.4554559 in 400  
Fitness: 0.4556806 in 500  
Fitness: 0.4559280 in 600  
Fitness: 0.4563006 in 700  
Fitness: 0.4567429 in 800  
Fitness: 0.4574212 in 900  
Fitness: 0.4581841 in 1000  
Fitness: 0.4592601 in 1100  
Fitness: 0.4606620 in 1200  
Fitness: 0.4624705 in 1300  
Fitness: 0.4648654 in 1400  
Fitness: 0.4676270 in 1500  
Fitness: 0.4697909 in 1600  
Fitness: 0.4697962 in 1700  
Fitness: 0.4697962 in 1800  
Fitness: 0.4697962 in 1900  
Fitness: 0.4697962 in 2000  
Fitness: 0.4697962 in 2100  
Fitness: 0.4697962 in 2200  
Fitness: 0.4697962 in 2300  
Fitness: 0.4697962 in 2400  
Fitness: 0.4697962 in 2500  
Fitness: 0.4697962 in 2600

Calculated Fitness Too Low. The process will automatically try again.!  
Calibration values:  
Fitness: 0.46979619207636103  
Maslow\_tlX: 22.4  
Maslow\_tlY: 2029.7  
Maslow\_trX: 3215.8  
Maslow\_trY: 2031.5  
Maslow\_blX: 0.0  
Maslow\_blY: 0.0  
Maslow\_brX: 3227.9  
Maslow\_brY: 0.0  
RestartingFitness: 0.4333104 in 100  
Fitness: 0.4333104 in 200  
Fitness: 0.4333104 in 300  
Fitness: 0.4333104 in 400  
Fitness: 0.4333104 in 500  
Fitness: 0.4333104 in 600  
Fitness: 0.4333104 in 700  
Fitness: 0.4333104 in 800  
Fitness: 0.4333104 in 900  
Fitness: 0.4333104 in 1000

Calculated Fitness Too Low. The process will automatically try again.!  
Calibration values:  
Fitness: 0.43331042709978873  
Maslow\_tlX: 50.4  
Maslow\_tlY: 2035.7  
Maslow\_trX: 3238.9  
Maslow\_trY: 1993.9  
Maslow\_blX: 0.0  
Maslow\_blY: 0.0  
Maslow\_brX: 3253.7  
Maslow\_brY: 0.0  
RestartingFitness: 0.4461467 in 100  
Fitness: 0.4461467 in 200  
Fitness: 0.4461467 in 300  
Fitness: 0.4461467 in 400  
Fitness: 0.4461467 in 500  
Fitness: 0.4461467 in 600  
Fitness: 0.4461467 in 700  
Fitness: 0.4461467 in 800  
Fitness: 0.4461467 in 900  
Fitness: 0.4461467 in 1000

---

<div class="post-metadata">

**Author:** ![VinileC](https://avatars.discourse-cdn.com/v4/letter/v/58956e/32.png) [@VinileC](https://forums.maslowcnc.com/u/VinileC)\
**Post date:** [May 21, 2025, 8:37am UTC](https://forums.maslowcnc.com/t/calibration-doesn-t-work/24124/13 "2025-05-21T08:37:35Z")

</div>

what should the fitness be?

---

<div class="post-metadata">

**Author:** ![VinileC](https://avatars.discourse-cdn.com/v4/letter/v/58956e/32.png) [@VinileC](https://forums.maslowcnc.com/u/VinileC)\
**Post date:** [May 21, 2025, 9:31am UTC](https://forums.maslowcnc.com/t/calibration-doesn-t-work/24124/14 "2025-05-21T09:31:27Z")

</div>

@bar @ian_ab so it looks like the calibration is better now. i did a full rest and new index and maslow.yaml file

its running through the fitness which is now around 0.6 but its at fitness figure in 70000 how many times does it do it? it hasnt restarted but seems to be going on for a long time?

---

<div class="post-metadata">

**Author:** ![VinileC](https://avatars.discourse-cdn.com/v4/letter/v/58956e/32.png) [@VinileC](https://forums.maslowcnc.com/u/VinileC)\
**Post date:** [May 21, 2025, 9:45am UTC](https://forums.maslowcnc.com/t/calibration-doesn-t-work/24124/15 "2025-05-21T09:45:22Z")

</div>

ITS ALIVE!!! finally after lots of troubleshooting its working. !! main problem was the board and the maslow and index files i think. thank you everyone for the help!

---

<div class="post-metadata">

**Author:** ![ian\_ab](https://avatars.discourse-cdn.com/v4/letter/i/a587f6/32.png) [@ian\_ab](https://forums.maslowcnc.com/u/ian_ab)\
**Post date:** [May 21, 2025, 9:51am UTC](https://forums.maslowcnc.com/t/calibration-doesn-t-work/24124/16 "2025-05-21T09:51:53Z")

</div>

Great, have fun with it now. Glad to be able to help
