# Extend, retract not working that well, setup missing size box

**URL:** <https://forums.maslowcnc.com/t/extend-retract-not-working-that-well-setup-missing-size-box/20994>\
**Category:** Troubleshooting\
**Created:** [May 8, 2024, 11:46pm UTC](https://forums.maslowcnc.com/t/extend-retract-not-working-that-well-setup-missing-size-box/20994 "2024-05-08T23:46:29Z")\
**Posts on this page:** 20\
**Page:** 1

<div class="post-metadata">

**Author:** ![BearFulmer](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/bearfulmer/32/24082_2.png) [@BearFulmer](https://forums.maslowcnc.com/u/BearFulmer)\
**Post date:** [May 8, 2024, 11:46pm UTC](https://forums.maslowcnc.com/t/extend-retract-not-working-that-well-setup-missing-size-box/20994/1 "2024-05-08T23:46:29Z")

</div>

extend and retract work a little but never fully, not after several tries, when assembling I was trying to have the least binding I could with the motor placement. extending fully doesnt leave enough time in that mode to extend all 4 fully, when you have to pull on two and then the remaining two, there is only enough time for one, be nice if this was a toggle or the timer duration was longer

there is no size box in the setup menu like the one bar uses in the video,

i feel testing the motors assembly would have been good before assembling the entire unit - just a thought.

i got the 4 anchor points attached to the frame but this thing is a hot mess trying to get it to do what its supposed to and not have it get tangled now

---

<div class="post-metadata">

**Author:** ![bar](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/bar/32/10_2.png) [@bar](https://forums.maslowcnc.com/u/bar)\
**Post date:** [May 9, 2024, 12:17am UTC](https://forums.maslowcnc.com/t/extend-retract-not-working-that-well-setup-missing-size-box/20994/2 "2024-05-09T00:17:27Z")

</div>

> [@BearFulmer](#):
>
> doesnt leave enough time in that mode to extend all 4 fully, when you have to pull on two and then the remaining two, there is only enough time for one, be nice if this was a toggle or the timer duration was longer

There isn’t a time limit on that mode…it should stay in that mode for as long as needed so I think that something else might be going wrong here.

> [@BearFulmer](#):
>
> there is no size box in the setup menu like the one bar uses in the video,

Have you updated to the latest firmware and index html file? Things are still changing pretty quickly so it’s worth getting the latest update so that everything works right

---

<div class="post-metadata">

**Author:** ![dlang](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/dlang/32/859_2.png) [@dlang](https://forums.maslowcnc.com/u/dlang)\
**Post date:** [May 9, 2024, 12:24am UTC](https://forums.maslowcnc.com/t/extend-retract-not-working-that-well-setup-missing-size-box/20994/3 "2024-05-09T00:24:55Z")

</div>

what version of firmware are you on?

David Lang

---

<div class="post-metadata">

**Author:** ![BearFulmer](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/bearfulmer/32/24082_2.png) [@BearFulmer](https://forums.maslowcnc.com/u/BearFulmer)\
**Post date:** [May 9, 2024, 12:46am UTC](https://forums.maslowcnc.com/t/extend-retract-not-working-that-well-setup-missing-size-box/20994/4 "2024-05-09T00:46:05Z")

</div>

the other issue having to do a retract all before extend, is that necessary to take off the anchors each time through setup

---

<div class="post-metadata">

**Author:** ![BearFulmer](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/bearfulmer/32/24082_2.png) [@BearFulmer](https://forums.maslowcnc.com/u/BearFulmer)\
**Post date:** [May 9, 2024, 12:49am UTC](https://forums.maslowcnc.com/t/extend-retract-not-working-that-well-setup-missing-size-box/20994/5 "2024-05-09T00:49:18Z")

</div>

.72 firmware,

I just deleted everything i have downloaded, redownloaded so there is no wrong files, then uploaded the yaml, index, and firmware files from the github

so the index file needs to stay as .gz i have figured out

I now have a matching interface with all the correct boxes on the setup screen. let me go from here now.

---

<div class="post-metadata">

**Author:** ![dlang](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/dlang/32/859_2.png) [@dlang](https://forums.maslowcnc.com/u/dlang)\
**Post date:** [May 9, 2024, 1:30am UTC](https://forums.maslowcnc.com/t/extend-retract-not-working-that-well-setup-missing-size-box/20994/6 "2024-05-09T01:30:54Z")

</div>

Bear Fulmer wrote:

> the other issue having to do a retract all before extend, is that necessary to take off the anchors each time through setup

Yes, you will be unable to fully retract with the belts attached to the anchors.

David Lang

---

<div class="post-metadata">

**Author:** ![dlang](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/dlang/32/859_2.png) [@dlang](https://forums.maslowcnc.com/u/dlang)\
**Post date:** [May 9, 2024, 1:33am UTC](https://forums.maslowcnc.com/t/extend-retract-not-working-that-well-setup-missing-size-box/20994/7 "2024-05-09T01:33:38Z")

</div>

Bear Fulmer wrote:

> .72 firmware,
> 
> I just deleted everything i have downloaded, redownloaded so there is no wrong files, then uploaded the yaml, index, and firmware files from the github
> 
> then i get upload rejected, not enough space. do i need to delete them first?

you should not, but make sure that you are uploading the files with exactly the  
same names (and make sure that the index.html.gz is getting uploaded compressed)

David Lang

---

<div class="post-metadata">

**Author:** ![BearFulmer](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/bearfulmer/32/24082_2.png) [@BearFulmer](https://forums.maslowcnc.com/u/BearFulmer)\
**Post date:** [May 9, 2024, 1:38am UTC](https://forums.maslowcnc.com/t/extend-retract-not-working-that-well-setup-missing-size-box/20994/8 "2024-05-09T01:38:25Z")

</div>

I got the firmware and files updated correctly, I will disconnect the four anchors and get back to trying to retract, then extending fully and see if that works correctly now.

about the 'machine size", what size is it referring to, is it the physical size of the frame, is it the size at the attachment points, is it the size of the spoil board, what size is it asking for?

---

<div class="post-metadata">

**Author:** ![BearFulmer](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/bearfulmer/32/24082_2.png) [@BearFulmer](https://forums.maslowcnc.com/u/BearFulmer)\
**Post date:** [May 9, 2024, 1:42am UTC](https://forums.maslowcnc.com/t/extend-retract-not-working-that-well-setup-missing-size-box/20994/9 "2024-05-09T01:42:15Z")

</div>

I would like to say thanks so far for the help and I would love to contribute to this possibly in the instructions to help remove some of the ambiguity

---

<div class="post-metadata">

**Author:** ![dlang](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/dlang/32/859_2.png) [@dlang](https://forums.maslowcnc.com/u/dlang)\
**Post date:** [May 9, 2024, 1:53am UTC](https://forums.maslowcnc.com/t/extend-retract-not-working-that-well-setup-missing-size-box/20994/10 "2024-05-09T01:53:37Z")

</div>

Bear Fulmer wrote:

> about the 'machine size", what size is it referring to, is it the physical size of the frame, is it the size at the attachment points, is it the size of the spoil board, what size is it asking for?

size of the anchor points.

This is a starting point for the calibration. It adjusts from these numbers, so  
it’s useful to have them in the ballpark (or you can do multiple calibration  
runs, each one getting closer to accurate)

David Lang

---

<div class="post-metadata">

**Author:** ![dlang](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/dlang/32/859_2.png) [@dlang](https://forums.maslowcnc.com/u/dlang)\
**Post date:** [May 9, 2024, 1:54am UTC](https://forums.maslowcnc.com/t/extend-retract-not-working-that-well-setup-missing-size-box/20994/11 "2024-05-09T01:54:27Z")

</div>

Bear Fulmer wrote:

> I would like to say thanks so far for the help and I would love to contribute  
> to this possibly in the instructions to help remove some of the ambiguity

This will help a lot, it doesn’t take long for us to get to where we know enough  
that we don’t understand that something isn’t clear.

David Lang

---

<div class="post-metadata">

**Author:** ![BearFulmer](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/bearfulmer/32/24082_2.png) [@BearFulmer](https://forums.maslowcnc.com/u/BearFulmer)\
**Post date:** [May 9, 2024, 2:17am UTC](https://forums.maslowcnc.com/t/extend-retract-not-working-that-well-setup-missing-size-box/20994/12 "2024-05-09T02:17:35Z")

</div>

ok, i got a full retract, then extended, it was roughly in the middle with the bottom two slack, it started calibration and then stopped in the middle of calibration,

the calibration went for about a minute,

now I got to pull it all off again and start over?

is there some way to have it save initial calibration data somehow so we dont have to do a full rectract, extension, once we put it on the frame after the very first time it should be good right?, really we are just calculating the same thing without all the extra work, it just throwing out our data seems not right.

---

<div class="post-metadata">

**Author:** ![dlang](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/dlang/32/859_2.png) [@dlang](https://forums.maslowcnc.com/u/dlang)\
**Post date:** [May 9, 2024, 2:38am UTC](https://forums.maslowcnc.com/t/extend-retract-not-working-that-well-setup-missing-size-box/20994/13 "2024-05-09T02:38:45Z")

</div>

Bear Fulmer wrote:

> ok, i got a full retract, then extended, it was roughly in the middle with the bottom two slack, it started calibration and then stopped in the middle of calibration,

what error did you get?

> the calibration went for about a minute,
> 
> now I got to pull it all off again and start over?
> 
> is there some way to have it save initial calibration data somehow so we dont have to do a full rectract, extension, once we put it on the frame after the very first time it should be good right?, really we are just calculating the same thing without all the extra work, it just throwing out our data seems not right.

There are two separate things happening here

1. getting to a known belt position (retract/extend)

right now, the maslow requires this every time you power cycle it. There is talk  
of a future version not requiring this, but if the belt spools move while it is  
powered off, the maslow has no way of knowing that the belt lengths have  
changed, which could cause grief.

the encoders measure the angle of the sprockets but do not know where the belt  
is (or how many turns the encoders have made). It only knows where the belts are  
when it retracts them until the motors hit their current limit (at which point  
it believes that they are fully retracted, i.e. length 0)

This work is pending until we get the calibration working better.

1. calibration (figuring out where the anchors really are in relation to each  
other)

This only needs to be done once (unless you change the frame), at the end it  
saves the new positions (it may do so after each stage of calibration, I’m not  
sure). you can look in the maslow.yaml file (either by downloading the file or  
in the settings tab) to see the maslow\_\* values that are currently saved.

David Lang

---

<div class="post-metadata">

**Author:** ![BearFulmer](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/bearfulmer/32/24082_2.png) [@BearFulmer](https://forums.maslowcnc.com/u/BearFulmer)\
**Post date:** [May 9, 2024, 4:01pm UTC](https://forums.maslowcnc.com/t/extend-retract-not-working-that-well-setup-missing-size-box/20994/14 "2024-05-09T16:01:28Z")

</div>

here is a copy of the maslow.yaml file as i turn it on this morning.  
is there a way to see if it had saved the correct values, well i guess it doesnt matter since you have to calibrate it every time the power cycles, i had no idea thats what it would take to use it

i thought maybe it could calibrate from 4 known points . like the four corners of the spoil board or something, maybe some magnets in the board like the prusa does.

board: Maslow  
name: Maslow S3 Board  
meta:  
Maslow\_vertical: true  
maslow\_calibration\_grid\_width\_mm\_X: 2000.000000  
maslow\_calibration\_grid\_height\_mm\_Y: 1000.000000  
maslow\_calibration\_grid\_size: 9  
Maslow\_brX: 2967.000000  
Maslow\_brY: 0.000000  
Maslow\_brZ: 117.000000  
Maslow\_tlX: 0.000000  
Maslow\_tlY: 2428.000000  
Maslow\_tlZ: 144.000000  
Maslow\_trX: 2967.000000  
Maslow\_trY: 2428.000000  
Maslow\_trZ: 97.000000  
Maslow\_blX: 0.000000  
Maslow\_blY: 0.000000  
Maslow\_blZ: 75.000000  
Maslow\_Retract\_Current\_Threshold: 1300  
Maslow\_Calibration\_Current\_Threshold: 1300  
stepping:  
engine: Timed  
idle\_ms: 240  
pulse\_us: 4  
dir\_delay\_us: 0  
disable\_delay\_us: 0  
segments: 12

uart1:  
txd\_pin: gpio.1  
rxd\_pin: gpio.2  
rts\_pin: NO\_PIN  
cts\_pin: NO\_PIN  
baud: 115200  
mode: 8N1

spi:  
miso\_pin: gpio.13  
mosi\_pin: gpio.11  
sck\_pin: gpio.12

sdcard:  
cs\_pin: gpio.10  
card\_detect\_pin: NO\_PIN  
frequency\_hz: 8000000

kinematics:  
Cartesian:

axes:  
shared\_stepper\_disable\_pin: NO\_PIN  
shared\_stepper\_reset\_pin: NO\_PIN  
x:  
steps\_per\_mm: 80.000000  
max\_rate\_mm\_per\_min: 2000.000000  
acceleration\_mm\_per\_sec2: 25.000000  
max\_travel\_mm: 2438.399902  
soft\_limits: false  
homing:  
cycle: -1  
allow\_single\_axis: true  
positive\_direction: true  
mpos\_mm: 0.000000  
feed\_mm\_per\_min: 50.000000  
seek\_mm\_per\_min: 200.000000  
settle\_ms: 250  
seek\_scaler: 1.100000  
feed\_scaler: 1.100000

```
motor0: 
  limit_neg_pin: NO_PIN
  limit_pos_pin: NO_PIN
  limit_all_pin: NO_PIN
  hard_limits: false
  pulloff_mm: 1.000000
  dc_servo: 
    id: 255
    timer_ms: 10

```

y:  
steps\_per\_mm: 80.000000  
max\_rate\_mm\_per\_min: 2000.000000  
acceleration\_mm\_per\_sec2: 25.000000  
max\_travel\_mm: 1219.199951  
soft\_limits: false  
homing:  
cycle: -1  
allow\_single\_axis: true  
positive\_direction: true  
mpos\_mm: 0.000000  
feed\_mm\_per\_min: 50.000000  
seek\_mm\_per\_min: 200.000000  
settle\_ms: 250  
seek\_scaler: 1.100000  
feed\_scaler: 1.100000

```
motor0: 
  limit_neg_pin: NO_PIN
  limit_pos_pin: NO_PIN
  limit_all_pin: NO_PIN
  hard_limits: false
  pulloff_mm: 1.000000
  null_motor: 

```

z:  
steps\_per\_mm: 100.000000  
max\_rate\_mm\_per\_min: 400.000000  
acceleration\_mm\_per\_sec2: 10.000000  
max\_travel\_mm: 100.000000  
soft\_limits: false  
homing:  
cycle: -1  
allow\_single\_axis: true  
positive\_direction: true  
mpos\_mm: 0.000000  
feed\_mm\_per\_min: 50.000000  
seek\_mm\_per\_min: 200.000000  
settle\_ms: 250  
seek\_scaler: 1.100000  
feed\_scaler: 1.100000

```
motor0: 
  limit_neg_pin: NO_PIN
  limit_pos_pin: NO_PIN
  limit_all_pin: NO_PIN
  hard_limits: false
  pulloff_mm: 1.000000
  tmc_2209: 
    uart_num: 1
    step_pin: gpio.15
    direction_pin: gpio.16
    disable_pin: NO_PIN
    r_sense_ohms: 0.110000
    run_amps: 1.000000
    hold_amps: 0.500000
    microsteps: 1
    toff_disable: 0
    toff_stealthchop: 5
    use_enable: true
    addr: 0
    run_mode: StealthChop
    homing_mode: StealthChop
    stallguard: 0
    stallguard_debug: false
    toff_coolstep: 3

motor1: 
  limit_neg_pin: NO_PIN
  limit_pos_pin: NO_PIN
  limit_all_pin: NO_PIN
  hard_limits: false
  pulloff_mm: 1.000000
  tmc_2209: 
    uart_num: 1
    step_pin: gpio.46
    direction_pin: gpio.38
    disable_pin: NO_PIN
    r_sense_ohms: 0.110000
    run_amps: 1.000000
    hold_amps: 0.500000
    microsteps: 1
    toff_disable: 0
    toff_stealthchop: 5
    use_enable: true
    addr: 1
    run_mode: StealthChop
    homing_mode: StealthChop
    stallguard: 0
    stallguard_debug: false
    toff_coolstep: 3

```

control:  
safety\_door\_pin: NO\_PIN  
reset\_pin: NO\_PIN  
feed\_hold\_pin: NO\_PIN  
cycle\_start\_pin: NO\_PIN  
macro0\_pin: NO\_PIN  
macro1\_pin: NO\_PIN  
macro2\_pin: NO\_PIN  
macro3\_pin: NO\_PIN

coolant:  
flood\_pin: NO\_PIN  
mist\_pin: NO\_PIN  
delay\_ms: 0

probe:  
pin: NO\_PIN  
check\_mode\_start: true

macros:  
startup\_line0:  
startup\_line1:  
macro0:  
macro1:  
macro2:  
macro3:

start:  
must\_home: true  
deactivate\_parking: false  
check\_limits: false

parking:  
enable: false  
axis: Z  
target\_mpos\_mm: -5.000000  
rate\_mm\_per\_min: 800.000000  
pullout\_distance\_mm: 5.000000  
pullout\_rate\_mm\_per\_min: 250.000000

user\_outputs:  
analog0\_pin: NO\_PIN  
analog1\_pin: NO\_PIN  
analog2\_pin: NO\_PIN  
analog3\_pin: NO\_PIN  
analog0\_hz: 5000  
analog1\_hz: 5000  
analog2\_hz: 5000  
analog3\_hz: 5000  
digital0\_pin: NO\_PIN  
digital1\_pin: NO\_PIN  
digital2\_pin: NO\_PIN  
digital3\_pin: NO\_PIN  
digital4\_pin: NO\_PIN  
digital5\_pin: NO\_PIN  
digital6\_pin: NO\_PIN  
digital7\_pin: NO\_PIN

NoSpindle:

arc\_tolerance\_mm: 0.002000  
junction\_deviation\_mm: 0.010000  
verbose\_errors: false  
report\_inches: false  
enable\_parking\_override\_control: false  
use\_line\_numbers: false  
planner\_blocks: 16

---

<div class="post-metadata">

**Author:** ![bar](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/bar/32/10_2.png) [@bar](https://forums.maslowcnc.com/u/bar)\
**Post date:** [May 9, 2024, 4:20pm UTC](https://forums.maslowcnc.com/t/extend-retract-not-working-that-well-setup-missing-size-box/20994/15 "2024-05-09T16:20:09Z")

</div>

> [@dlang](#):
>
> what error did you get?

I think that this is the import question

Your results should be automatically saved for you as long as the machine thinks they are good enough to be worth saving (fitness more than 0.5)

---

<div class="post-metadata">

**Author:** ![BearFulmer](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/bearfulmer/32/24082_2.png) [@BearFulmer](https://forums.maslowcnc.com/u/BearFulmer)\
**Post date:** [May 9, 2024, 4:52pm UTC](https://forums.maslowcnc.com/t/extend-retract-not-working-that-well-setup-missing-size-box/20994/16 "2024-05-09T16:52:05Z")

</div>

it said the motors were not safe to move or something, i did not write it down, when i opened up the setup screen it had not saved the vertical orientation possibly, i rechecked everything

this morning about 5 mins ago it finished calibration successfully.

I thought when i pressed extend all that it meant the same as retract all, all being the entire belt length, so after retraction I was expecting the extend to go the length of the belt and not off a dimension, i understand that it uses the setup dimensions to extend them just enough  
to put it roughly in the center.

now that it has calibrated is this only good until i shut the machine off?

---

<div class="post-metadata">

**Author:** ![bar](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/bar/32/10_2.png) [@bar](https://forums.maslowcnc.com/u/bar)\
**Post date:** [May 9, 2024, 4:55pm UTC](https://forums.maslowcnc.com/t/extend-retract-not-working-that-well-setup-missing-size-box/20994/17 "2024-05-09T16:55:14Z")

</div>

> [@BearFulmer](#):
>
> now that it has calibrated is this only good until i shut the machine off?

No, calibration is a one time thing. You won’t need to do it again unless you build a new frame with different anchor point locations.

If you turn the machine off you will need to do Retract All → Extend All → Take Slack to extend the belts and attach them to the frame again.

---

<div class="post-metadata">

**Author:** ![dlang](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/dlang/32/859_2.png) [@dlang](https://forums.maslowcnc.com/u/dlang)\
**Post date:** [May 9, 2024, 4:55pm UTC](https://forums.maslowcnc.com/t/extend-retract-not-working-that-well-setup-missing-size-box/20994/18 "2024-05-09T16:55:15Z")

</div>

Bear Fulmer wrote:

> here is a copy of the maslow.yaml file as i turn it on this morning.  
> is there a way to see if it had saved the correct values, well i guess it doesnt matter since you have to calibrate it every time the power cycles, i had no idea thats what it would take to use it

what calibration sets are:

> Maslow\_brX: 2967.000000  
> Maslow\_brY: 0.000000  
> Maslow\_tlX: 0.000000  
> Maslow\_tlY: 2428.000000  
> Maslow\_trX: 2967.000000  
> Maslow\_trY: 2428.000000  
> Maslow\_blX: 0.000000  
> Maslow\_blY: 0.000000

These look like the numbers that you entered manually, so it probably did not  
save anything as a result of your calibration (nothing after the decimal,  
everything a perfect rectangle is unlikely in the real world)

> Maslow\_Retract\_Current\_Threshold: 1300  
> Maslow\_Calibration\_Current\_Threshold: 1300

@bar, we should change the UI so that when the retraction is set, the  
calibration is set as well

> i thought maybe it could calibrate from 4 known points . like the four corners of the spoil board or something, maybe some magnets in the board like the prusa does.

The problem is that those aren’t really known points. their distance can vary  
slightly depending on the spoil board (which also may not be a perfect  
rectangle) and we don’t know where they are in relationship to the anchors.

there are some discussion threads on other ways to do calibration, and ideas are  
welcome. I would suggest starting a new thread and trying to work out the math  
there. Remember, the only things you really ‘know’ are the Z offset to the  
anchors and the length of the belts (and the Z offsets are only somewhat known)

David Lang

---

<div class="post-metadata">

**Author:** ![BearFulmer](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/bearfulmer/32/24082_2.png) [@BearFulmer](https://forums.maslowcnc.com/u/BearFulmer)\
**Post date:** [May 9, 2024, 8:37pm UTC](https://forums.maslowcnc.com/t/extend-retract-not-working-that-well-setup-missing-size-box/20994/19 "2024-05-09T20:37:17Z")

</div>

just for follow up here is what it looks like now

board: Maslow  
name: Maslow S3 Board  
meta:  
Maslow\_vertical: true  
maslow\_calibration\_grid\_width\_mm\_X: 2000.000000  
maslow\_calibration\_grid\_height\_mm\_Y: 1000.000000  
maslow\_calibration\_grid\_size: 9  
Maslow\_brX: 2945.899902  
Maslow\_brY: 0.000000  
Maslow\_brZ: 117.000000  
Maslow\_tlX: -4.300000  
Maslow\_tlY: 2422.399902  
Maslow\_tlZ: 144.000000  
Maslow\_trX: 2942.699951  
Maslow\_trY: 2421.199951  
Maslow\_trZ: 97.000000  
Maslow\_blX: 0.000000  
Maslow\_blY: 0.000000  
Maslow\_blZ: 75.000000  
Maslow\_Retract\_Current\_Threshold: 1300  
Maslow\_Calibration\_Current\_Threshold: 1300  
stepping:  
engine: Timed  
idle\_ms: 240  
pulse\_us: 4  
dir\_delay\_us: 0  
disable\_delay\_us: 0  
segments: 12

uart1:  
txd\_pin: gpio.1  
rxd\_pin: gpio.2  
rts\_pin: NO\_PIN  
cts\_pin: NO\_PIN  
baud: 115200  
mode: 8N1

spi:  
miso\_pin: gpio.13  
mosi\_pin: gpio.11  
sck\_pin: gpio.12

sdcard:  
cs\_pin: gpio.10  
card\_detect\_pin: NO\_PIN  
frequency\_hz: 8000000

kinematics:  
Cartesian:

axes:  
shared\_stepper\_disable\_pin: NO\_PIN  
shared\_stepper\_reset\_pin: NO\_PIN  
x:  
steps\_per\_mm: 80.000000  
max\_rate\_mm\_per\_min: 2000.000000  
acceleration\_mm\_per\_sec2: 25.000000  
max\_travel\_mm: 2438.399902  
soft\_limits: false  
homing:  
cycle: -1  
allow\_single\_axis: true  
positive\_direction: true  
mpos\_mm: 0.000000  
feed\_mm\_per\_min: 50.000000  
seek\_mm\_per\_min: 200.000000  
settle\_ms: 250  
seek\_scaler: 1.100000  
feed\_scaler: 1.100000

```
motor0: 
  limit_neg_pin: NO_PIN
  limit_pos_pin: NO_PIN
  limit_all_pin: NO_PIN
  hard_limits: false
  pulloff_mm: 1.000000
  dc_servo: 
    id: 255
    timer_ms: 10

```

y:  
steps\_per\_mm: 80.000000  
max\_rate\_mm\_per\_min: 2000.000000  
acceleration\_mm\_per\_sec2: 25.000000  
max\_travel\_mm: 1219.199951  
soft\_limits: false  
homing:  
cycle: -1  
allow\_single\_axis: true  
positive\_direction: true  
mpos\_mm: 0.000000  
feed\_mm\_per\_min: 50.000000  
seek\_mm\_per\_min: 200.000000  
settle\_ms: 250  
seek\_scaler: 1.100000  
feed\_scaler: 1.100000

```
motor0: 
  limit_neg_pin: NO_PIN
  limit_pos_pin: NO_PIN
  limit_all_pin: NO_PIN
  hard_limits: false
  pulloff_mm: 1.000000
  null_motor: 

```

z:  
steps\_per\_mm: 100.000000  
max\_rate\_mm\_per\_min: 400.000000  
acceleration\_mm\_per\_sec2: 10.000000  
max\_travel\_mm: 100.000000  
soft\_limits: false  
homing:  
cycle: -1  
allow\_single\_axis: true  
positive\_direction: true  
mpos\_mm: 0.000000  
feed\_mm\_per\_min: 50.000000  
seek\_mm\_per\_min: 200.000000  
settle\_ms: 250  
seek\_scaler: 1.100000  
feed\_scaler: 1.100000

```
motor0: 
  limit_neg_pin: NO_PIN
  limit_pos_pin: NO_PIN
  limit_all_pin: NO_PIN
  hard_limits: false
  pulloff_mm: 1.000000
  tmc_2209: 
    uart_num: 1
    step_pin: gpio.15
    direction_pin: gpio.16
    disable_pin: NO_PIN
    r_sense_ohms: 0.110000
    run_amps: 1.000000
    hold_amps: 0.500000
    microsteps: 1
    toff_disable: 0
    toff_stealthchop: 5
    use_enable: true
    addr: 0
    run_mode: StealthChop
    homing_mode: StealthChop
    stallguard: 0
    stallguard_debug: false
    toff_coolstep: 3

motor1: 
  limit_neg_pin: NO_PIN
  limit_pos_pin: NO_PIN
  limit_all_pin: NO_PIN
  hard_limits: false
  pulloff_mm: 1.000000
  tmc_2209: 
    uart_num: 1
    step_pin: gpio.46
    direction_pin: gpio.38
    disable_pin: NO_PIN
    r_sense_ohms: 0.110000
    run_amps: 1.000000
    hold_amps: 0.500000
    microsteps: 1
    toff_disable: 0
    toff_stealthchop: 5
    use_enable: true
    addr: 1
    run_mode: StealthChop
    homing_mode: StealthChop
    stallguard: 0
    stallguard_debug: false
    toff_coolstep: 3

```

control:  
safety\_door\_pin: NO\_PIN  
reset\_pin: NO\_PIN  
feed\_hold\_pin: NO\_PIN  
cycle\_start\_pin: NO\_PIN  
macro0\_pin: NO\_PIN  
macro1\_pin: NO\_PIN  
macro2\_pin: NO\_PIN  
macro3\_pin: NO\_PIN

coolant:  
flood\_pin: NO\_PIN  
mist\_pin: NO\_PIN  
delay\_ms: 0

probe:  
pin: NO\_PIN  
check\_mode\_start: true

macros:  
startup\_line0:  
startup\_line1:  
macro0:  
macro1:  
macro2:  
macro3:

start:  
must\_home: true  
deactivate\_parking: false  
check\_limits: false

parking:  
enable: false  
axis: Z  
target\_mpos\_mm: -5.000000  
rate\_mm\_per\_min: 800.000000  
pullout\_distance\_mm: 5.000000  
pullout\_rate\_mm\_per\_min: 250.000000

user\_outputs:  
analog0\_pin: NO\_PIN  
analog1\_pin: NO\_PIN  
analog2\_pin: NO\_PIN  
analog3\_pin: NO\_PIN  
analog0\_hz: 5000  
analog1\_hz: 5000  
analog2\_hz: 5000  
analog3\_hz: 5000  
digital0\_pin: NO\_PIN  
digital1\_pin: NO\_PIN  
digital2\_pin: NO\_PIN  
digital3\_pin: NO\_PIN  
digital4\_pin: NO\_PIN  
digital5\_pin: NO\_PIN  
digital6\_pin: NO\_PIN  
digital7\_pin: NO\_PIN

NoSpindle:

arc\_tolerance\_mm: 0.002000  
junction\_deviation\_mm: 0.010000  
verbose\_errors: false  
report\_inches: false  
enable\_parking\_override\_control: false  
use\_line\_numbers: false  
planner\_blocks: 16

---

<div class="post-metadata">

**Author:** ![bar](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/bar/32/10_2.png) [@bar](https://forums.maslowcnc.com/u/bar)\
**Post date:** [May 9, 2024, 8:53pm UTC](https://forums.maslowcnc.com/t/extend-retract-not-working-that-well-setup-missing-size-box/20994/20 "2024-05-09T20:53:34Z")

</div>

> [@BearFulmer](#):
>
> Maslow\_brX: 2945.899902  
> Maslow\_brY: 0.000000  
> Maslow\_brZ: 117.000000  
> Maslow\_tlX: -4.300000  
> Maslow\_tlY: 2422.399902  
> Maslow\_tlZ: 144.000000  
> Maslow\_trX: 2942.699951  
> Maslow\_trY: 2421.199951  
> Maslow\_trZ: 97.000000  
> Maslow\_blX: 0.000000  
> Maslow\_blY: 0.000000  
> Maslow\_blZ: 75.000000

This is the important part, we can see here that those numbers have been computed by the calibration process and aren’t the numbers that you entered anymore

[Next page](https://forums.maslowcnc.com/t/extend-retract-not-working-that-well-setup-missing-size-box/20994.md?page=2)
