# M2 calibration missing setting to set sled size **URL:** \ **Category:** Uncategorized\ **Tags:** calibration\ **Created:** [November 14, 2024, 6:51am UTC](https://forums.maslowcnc.com/t/m2-calibration-missing-setting-to-set-sled-size/22726 "2024-11-14T06:51:59Z")\ **Posts on this page:** 20\ **Page:** 1
**Author:** ![Nolan](https://avatars.discourse-cdn.com/v4/letter/n/aeb1de/32.png) [@Nolan](https://forums.maslowcnc.com/u/Nolan)\ **Post date:** [November 14, 2024, 6:51am UTC](https://forums.maslowcnc.com/t/m2-calibration-missing-setting-to-set-sled-size/22726/1 "2024-11-14T06:51:59Z")
I can’t seem to find the settings to edit the sled size in makerverse. This must matter when doing Edge calibration. My m2 sled is custom, I do not have the blue m2 sled. Mine is 25mm radius. ---
**Author:** ![TimS](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/tims/32/17329_2.png) [@TimS](https://forums.maslowcnc.com/u/TimS)\ **Post date:** [November 14, 2024, 7:54am UTC](https://forums.maslowcnc.com/t/m2-calibration-missing-setting-to-set-sled-size/22726/2 "2024-11-14T07:54:33Z")
Is it the version with the DUE board or Arduino? If it’s the Arduino, go with webcontrol, it’s easier to use imo. If you want to stick (or have to with the DUE board) with makerverse you may have to contact makermade since they made that version and that software. ---
**Author:** ![Jeremiad](https://avatars.discourse-cdn.com/v4/letter/j/13edae/32.png) [@Jeremiad](https://forums.maslowcnc.com/u/Jeremiad)\ **Post date:** [November 15, 2024, 2:48am UTC](https://forums.maslowcnc.com/t/m2-calibration-missing-setting-to-set-sled-size/22726/3 "2024-11-15T02:48:23Z")
In Makerverse, the Firmware window should indicate whether you have Arduino or DUE. Just below that is the Calibrate button. Click Calibrate, click Let’s Begin!, and then select the tab that says Sled. You can select Other, and specify the size of your sled. You may enter your values to each edge (from the bit) there. For reference, I have the standard ‘blue’ sled, and each measurement with the router perfectly centered is 229.5mm from bit to edge. Cheers. ---
**Author:** ![Nolan](https://avatars.discourse-cdn.com/v4/letter/n/aeb1de/32.png) [@Nolan](https://forums.maslowcnc.com/u/Nolan)\ **Post date:** [November 16, 2024, 4:28pm UTC](https://forums.maslowcnc.com/t/m2-calibration-missing-setting-to-set-sled-size/22726/4 "2024-11-16T16:28:40Z")
I do have the Due board, just a custom sled & z assembly ---
**Author:** ![Nolan](https://avatars.discourse-cdn.com/v4/letter/n/aeb1de/32.png) [@Nolan](https://forums.maslowcnc.com/u/Nolan)\ **Post date:** [November 16, 2024, 4:28pm UTC](https://forums.maslowcnc.com/t/m2-calibration-missing-setting-to-set-sled-size/22726/5 "2024-11-16T16:28:58Z")
Maybe I’m on an old version of maker verse, I do not have a sled tab ---
**Author:** ![Jeremiad](https://avatars.discourse-cdn.com/v4/letter/j/13edae/32.png) [@Jeremiad](https://forums.maslowcnc.com/u/Jeremiad)\ **Post date:** [November 16, 2024, 5:06pm UTC](https://forums.maslowcnc.com/t/m2-calibration-missing-setting-to-set-sled-size/22726/6 "2024-11-16T17:06:10Z")
When I open Makerverse and connect to the machine, the console identifies my version as Makerverse 1.1.3. Just under the console window is Maslow, click the Info (i) button, and under Controller Settings, I am showing GRBL version 1.1g, and MaslowDue version 20200915. I’m sure I have a copy of the install program, but I’m not sure I can upload an executable file here. Do a search for Makerverse 1.1.3 download, and if it doesn’t work, let me know and I will see what I can do. ---
**Author:** ![Nolan](https://avatars.discourse-cdn.com/v4/letter/n/aeb1de/32.png) [@Nolan](https://forums.maslowcnc.com/u/Nolan)\ **Post date:** [November 16, 2024, 6:26pm UTC](https://forums.maslowcnc.com/t/m2-calibration-missing-setting-to-set-sled-size/22726/7 "2024-11-16T18:26:53Z")
So I am actually on MakerHub v 1.3.1 Beta ( newest available from the maker-made site ). GRBL 1.1g ---
**Author:** ![Nolan](https://avatars.discourse-cdn.com/v4/letter/n/aeb1de/32.png) [@Nolan](https://forums.maslowcnc.com/u/Nolan)\ **Post date:** [November 16, 2024, 6:36pm UTC](https://forums.maslowcnc.com/t/m2-calibration-missing-setting-to-set-sled-size/22726/8 "2024-11-16T18:36:34Z")
1.1.3 will not run on my computer. it crashes I’m going to try 1.1.4 ---
**Author:** ![Nolan](https://avatars.discourse-cdn.com/v4/letter/n/aeb1de/32.png) [@Nolan](https://forums.maslowcnc.com/u/Nolan)\ **Post date:** [November 16, 2024, 6:51pm UTC](https://forums.maslowcnc.com/t/m2-calibration-missing-setting-to-set-sled-size/22726/9 "2024-11-16T18:51:31Z")
None of the makerverse versions run on my mac. ---
**Author:** ![Jeremiad](https://avatars.discourse-cdn.com/v4/letter/j/13edae/32.png) [@Jeremiad](https://forums.maslowcnc.com/u/Jeremiad)\ **Post date:** [November 16, 2024, 8:46pm UTC](https://forums.maslowcnc.com/t/m2-calibration-missing-setting-to-set-sled-size/22726/10 "2024-11-16T20:46:08Z")
I can’t offer you much on the Mac side of things. I stopped working on Mac stuff some twenty years ago. You can try to reach out to TJ Weber @sourcery or [info@makermade.com](mailto:info@makermade.com) and see if they can help you more. I know there can be a lot of division between Mac and PC, but I would seriously suggest picking up a used laptop running Windows, and I think you would be in a better position for getting help. ---
**Author:** ![Nolan](https://avatars.discourse-cdn.com/v4/letter/n/aeb1de/32.png) [@Nolan](https://forums.maslowcnc.com/u/Nolan)\ **Post date:** [November 18, 2024, 10:40pm UTC](https://forums.maslowcnc.com/t/m2-calibration-missing-setting-to-set-sled-size/22726/11 "2024-11-18T22:40:28Z")
What is the trick to opening 1.1.3, I keep getting a network error in every version of Makerverse I try to run, on both Mac or PC. ---
**Author:** ![Nolan](https://avatars.discourse-cdn.com/v4/letter/n/aeb1de/32.png) [@Nolan](https://forums.maslowcnc.com/u/Nolan)\ **Post date:** [November 18, 2024, 10:40pm UTC](https://forums.maslowcnc.com/t/m2-calibration-missing-setting-to-set-sled-size/22726/12 "2024-11-18T22:40:52Z")
I’m getting nowhere with Tech Support, the guy answering emails is clueless as to what I’m talking about. ---
**Author:** ![bar](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/bar/32/10_2.png) [@bar](https://forums.maslowcnc.com/u/bar)\ **Post date:** [November 19, 2024, 12:57am UTC](https://forums.maslowcnc.com/t/m2-calibration-missing-setting-to-set-sled-size/22726/13 "2024-11-19T00:57:44Z")
I’m sorry that I can’t help more, I’ve never actually used Makerverse 😕 . Just to make it clear MakerMade who makes that software is a different company that puts our logo on their products without permission, we are not connected to them in any way ---
**Author:** ![Nolan](https://avatars.discourse-cdn.com/v4/letter/n/aeb1de/32.png) [@Nolan](https://forums.maslowcnc.com/u/Nolan)\ **Post date:** [November 19, 2024, 1:46am UTC](https://forums.maslowcnc.com/t/m2-calibration-missing-setting-to-set-sled-size/22726/14 "2024-11-19T01:46:01Z")
what do you use ? ---
**Author:** ![dlang](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/dlang/32/859_2.png) [@dlang](https://forums.maslowcnc.com/u/dlang)\ **Post date:** [November 19, 2024, 2:20am UTC](https://forums.maslowcnc.com/t/m2-calibration-missing-setting-to-set-sled-size/22726/15 "2024-11-19T02:20:47Z")
Nolan Craw wrote: > what do you use ? The entire M2 machine as well as the software related to it was created by Makermade. Bar has never used it or had anything directly to do with it’s design. Makermade attempted to improve the Maslow design that Bar created, and may have done so. But instead of working with the community and making their machine work with the same software everyone else used, they attempted to create their own community (as well as their own software), but then started pointing people here for answers. We attempt to help users, but are limited in what we can do. David Lang ---
**Author:** ![TimS](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/tims/32/17329_2.png) [@TimS](https://forums.maslowcnc.com/u/TimS)\ **Post date:** [November 19, 2024, 2:21am UTC](https://forums.maslowcnc.com/t/m2-calibration-missing-setting-to-set-sled-size/22726/16 "2024-11-19T02:21:53Z")
Since you have a M2 with a DUE board, you have no choice but to use makerverse. Someone on the forums can surely help. I can’t provide much because I have a classic that I use webcontrol to run. ---
**Author:** ![Nolan](https://avatars.discourse-cdn.com/v4/letter/n/aeb1de/32.png) [@Nolan](https://forums.maslowcnc.com/u/Nolan)\ **Post date:** [November 19, 2024, 6:21am UTC](https://forums.maslowcnc.com/t/m2-calibration-missing-setting-to-set-sled-size/22726/17 "2024-11-19T06:21:25Z")
Do you mean makerhub ? I’ve been told NOT to use makerverse lol ---
**Author:** ![Nolan](https://avatars.discourse-cdn.com/v4/letter/n/aeb1de/32.png) [@Nolan](https://forums.maslowcnc.com/u/Nolan)\ **Post date:** [November 19, 2024, 6:22am UTC](https://forums.maslowcnc.com/t/m2-calibration-missing-setting-to-set-sled-size/22726/18 "2024-11-19T06:22:33Z")
Ugh. I’m starting to feel less shy about my distain. ---
**Author:** ![TimS](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/tims/32/17329_2.png) [@TimS](https://forums.maslowcnc.com/u/TimS)\ **Post date:** [November 19, 2024, 2:46pm UTC](https://forums.maslowcnc.com/t/m2-calibration-missing-setting-to-set-sled-size/22726/19 "2024-11-19T14:46:18Z")
According to their website makerhub replaced makerverse. ---
**Author:** ![Nolan](https://avatars.discourse-cdn.com/v4/letter/n/aeb1de/32.png) [@Nolan](https://forums.maslowcnc.com/u/Nolan)\ **Post date:** [November 19, 2024, 3:36pm UTC](https://forums.maslowcnc.com/t/m2-calibration-missing-setting-to-set-sled-size/22726/20 "2024-11-19T15:36:22Z")
Yes, of that I am aware. That’s why I wanted clarification [Next page](https://forums.maslowcnc.com/t/m2-calibration-missing-setting-to-set-sled-size/22726.md?page=2)