# MakerCam is down HELP! **URL:** \ **Category:** MakerCam\ **Created:** [August 20, 2021, 10:24am UTC](https://forums.maslowcnc.com/t/makercam-is-down-help/17029 "2021-08-20T10:24:22Z")\ **Posts on this page:** 9\ **Page:** 1
**Author:** ![CycloRetro](https://avatars.discourse-cdn.com/v4/letter/c/b77776/32.png) [@CycloRetro](https://forums.maslowcnc.com/u/CycloRetro)\ **Post date:** [August 20, 2021, 10:24am UTC](https://forums.maslowcnc.com/t/makercam-is-down-help/17029/1 "2021-08-20T10:24:22Z")
MakerCam went down yesterday and I don’t think it’s coming back. Is there a way to get it back or use it offline or something very similar to it? ---
**Author:** ![The\_Cat\_In\_The\_Hat](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/the_cat_in_the_hat/32/18923_2.png) [@The\_Cat\_In\_The\_Hat](https://forums.maslowcnc.com/u/The_Cat_In_The_Hat)\ **Post date:** [August 20, 2021, 1:36pm UTC](https://forums.maslowcnc.com/t/makercam-is-down-help/17029/2 "2021-08-20T13:36:49Z")
I used Easel instead of MC. Easel was a lot easier and better to use. However, it is something that you have to pay for but there is a free trial. ---
**Author:** ![mooselake](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/mooselake/32/6218_2.png) [@mooselake](https://forums.maslowcnc.com/u/mooselake)\ **Post date:** [August 20, 2021, 2:05pm UTC](https://forums.maslowcnc.com/t/makercam-is-down-help/17029/3 "2021-08-20T14:05:22Z")
Makercam us dead and gone, and will never work again. It’s gone to the same well earned retirement beach community as many other older defunct programs. Krabzcam is a rewrite in javascript and likely the closest free replacement. After chasing Easel’s regular problems in another forum I’d recommend you stay away from it, Carbide Create works well for many and skips the increasingly pay aspect of Easel. However you will trade Easel’s drag and droppy interface for something more traditional. Or check out krabzcam which gets good reports. ---
**Author:** ![CycloRetro](https://avatars.discourse-cdn.com/v4/letter/c/b77776/32.png) [@CycloRetro](https://forums.maslowcnc.com/u/CycloRetro)\ **Post date:** [August 21, 2021, 1:21am UTC](https://forums.maslowcnc.com/t/makercam-is-down-help/17029/4 "2021-08-21T01:21:13Z")
Thanks, I like the sound of Krabzcam and Carbide Create. I’ll try both. Its a shame about MakerCam, it was so easy and quick to use. Does anyone have an offline copy of MakerCam? I’d be willing to buy a version. ---
**Author:** ![dlang](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/dlang/32/859_2.png) [@dlang](https://forums.maslowcnc.com/u/dlang)\ **Post date:** [August 21, 2021, 1:33am UTC](https://forums.maslowcnc.com/t/makercam-is-down-help/17029/5 "2021-08-21T01:33:30Z")
the problem is that makercam was written in flash, and flash is now dead and removed from all browsers, so you can’t run it. David Lang ---
**Author:** ![bar](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/bar/32/10_2.png) [@bar](https://forums.maslowcnc.com/u/bar)\ **Post date:** [August 21, 2021, 6:06pm UTC](https://forums.maslowcnc.com/t/makercam-is-down-help/17029/6 "2021-08-21T18:06:33Z")
You can download it from their GitHub page [GitHub - Jack000/PartKAM: A browser-based 2.5D CAM tool](https://github.com/Jack000/PartKAM) but @dlang is right that it might be hard to get it to run in a modern browser ---
**Author:** ![CycloRetro](https://avatars.discourse-cdn.com/v4/letter/c/b77776/32.png) [@CycloRetro](https://forums.maslowcnc.com/u/CycloRetro)\ **Post date:** [August 21, 2021, 11:47pm UTC](https://forums.maslowcnc.com/t/makercam-is-down-help/17029/7 "2021-08-21T23:47:49Z")
Maybe that will work for me because as of Thursday the 19th I was still using MakerCam just fine, it only went down for me when MakerCam stopped their domain name registration with Go Daddy ---
**Author:** ![CycloRetro](https://avatars.discourse-cdn.com/v4/letter/c/b77776/32.png) [@CycloRetro](https://forums.maslowcnc.com/u/CycloRetro)\ **Post date:** [August 21, 2021, 11:58pm UTC](https://forums.maslowcnc.com/t/makercam-is-down-help/17029/8 "2021-08-21T23:58:52Z")
Thanks for that but none of those links work anymore ---
**Author:** ![Jamtek](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/jamtek/32/12604_2.png) [@Jamtek](https://forums.maslowcnc.com/u/Jamtek)\ **Post date:** [August 22, 2021, 2:53am UTC](https://forums.maslowcnc.com/t/makercam-is-down-help/17029/9 "2021-08-22T02:53:51Z")
May not be worth the effort but it is possible to run it in the Adobe debugger that is still downloadable. Shapeoko still has a link to a standalone (compiled) SWF version of MakerCam on their Wiki. [https://wiki.shapeoko.com/index.php/MakerCAM](https://wiki.shapeoko.com/index.php/MakerCAM) Then download the ‘Flash Player projector content debugger’ from the Adobe website. [https://www.adobe.com/support/flashplayer/debug\_downloads.html](https://www.adobe.com/support/flashplayer/debug_downloads.html) Run the Adobe player and select file, open the partkam.swf file you downloaded from Shapeoko. ![image](https://canada1.discourse-cdn.com/flex031/uploads/maslowcnc/original/3X/0/8/0856570e8f02024270270a4d3c30e073e40b10a4.png) Out of nostalgia I was able to run it on a Windows 10 PC. But as others have mentioned with so many other free or low cost options perhaps it’s time to move on.