# Maslow kits for sale soon.
**URL:** https://forums.maslowcnc.com/t/maslow-kits-for-sale-soon/7581
**Category:** Maslow Community
**Created:** [November 4, 2018, 9:30pm UTC](https://forums.maslowcnc.com/t/maslow-kits-for-sale-soon/7581 "2018-11-04T21:30:38Z")
**Posts on this page:** 13
**Page:** 1
### Author:  [@GardenRobot](https://forums.maslowcnc.com/u/GardenRobot)
#### Post date: [November 4, 2018, 9:30pm UTC](https://forums.maslowcnc.com/t/maslow-kits-for-sale-soon/7581/1 "2018-11-04T21:30:38Z")
* * *
This is a companion discussion topic for the original entry at [http://maslowcommunitygarden.org/Maslow-kits-for-sale-soon..html](http://maslowcommunitygarden.org/Maslow-kits-for-sale-soon..html)
---
### Author:  [@jwolter](https://forums.maslowcnc.com/u/jwolter)
#### Post date: [November 5, 2018, 12:11am UTC](https://forums.maslowcnc.com/t/maslow-kits-for-sale-soon/7581/2 "2018-11-05T00:11:51Z")
---
### Author:  [@jwolter](https://forums.maslowcnc.com/u/jwolter)
#### Post date: [November 5, 2018, 12:14am UTC](https://forums.maslowcnc.com/t/maslow-kits-for-sale-soon/7581/3 "2018-11-05T00:14:10Z")
Just for clarification, this looks to me like the @MakerMadeCNC original design Maslow, as opposed to the @Metalmaslow modified design version, correct?
---
### Author:  [@Metalmaslow](https://forums.maslowcnc.com/u/Metalmaslow)
#### Post date: [November 5, 2018, 12:44am UTC](https://forums.maslowcnc.com/t/maslow-kits-for-sale-soon/7581/4 "2018-11-05T00:44:18Z")
They are offering the updated motor circuit board and I think the rest of the pieces are the same as the original but best to hear it from the horses mouth
---
### Author:  [@2cents](https://forums.maslowcnc.com/u/2cents)
#### Post date: [November 6, 2018, 3:28am UTC](https://forums.maslowcnc.com/t/maslow-kits-for-sale-soon/7581/5 "2018-11-06T03:28:07Z")
Hi there!
Yes it’s the original kit with a bit thicker ring and carriage, also we’ve modified the original TLE5206. @blurfl did an amazing job creating this board, we just tweaked the pcb a little.
> **[Shield based on the TLE5206](https://www.eastbaysource.com/products/power-control-shield-based-on-the-tle5206-h-bridge-from-infineon-technologies)**
>
> This board uses three TLE5206, from Infineon Technologies, to power the X,Y and Z motors independently. This is our version of the original TLE5206 board, designed by @blurfl for the Maslow community, with the following modifications. The PCB is now...
---
### Author:  [@blurfl](https://forums.maslowcnc.com/u/blurfl)
#### Post date: [November 6, 2018, 4:34am UTC](https://forums.maslowcnc.com/t/maslow-kits-for-sale-soon/7581/6 "2018-11-06T04:34:36Z")
There are many nice changes, a job well done!
I’m curious about the pins used for identifying the board version and for the AUX functions. Will the board identify as a new version number? That information is used by the firmware to assign gpio pins for the AUX, very different from version to version.
---
### Author:  [@2cents](https://forums.maslowcnc.com/u/2cents)
#### Post date: [November 7, 2018, 3:35am UTC](https://forums.maslowcnc.com/t/maslow-kits-for-sale-soon/7581/7 "2018-11-07T03:35:02Z")
Hi blurfl
Thanks to you for creating this board! We’ve just polished it a little 🙂
No changes to the firmware needed, it identifies as 1.4
---
### Author:  [@blurfl](https://forums.maslowcnc.com/u/blurfl)
#### Post date: [November 7, 2018, 3:49am UTC](https://forums.maslowcnc.com/t/maslow-kits-for-sale-soon/7581/8 "2018-11-07T03:49:23Z")
> [@2cents](#):
>
> We’ve just polished it a little
Improvements are a good thing. Will the files be available?
> [@2cents](#):
>
> No changes to the firmware needed, it identifies as 1.4
That’s the same as the CommunityGarden version then. 👍 Note that the firmware identifies the TLE5206 board as “PCB v1.3 TLE5206 Detected” in GC (for historical reasons pcbVersion is the strapped value minus 1).
It surprised me that the AUX functions weren’t implemented. Can you share the reasoning?
---
### Author:  [@2cents](https://forums.maslowcnc.com/u/2cents)
#### Post date: [November 7, 2018, 5:07am UTC](https://forums.maslowcnc.com/t/maslow-kits-for-sale-soon/7581/9 "2018-11-07T05:07:55Z")
> [@blurfl](#):
>
> Improvements are a good thing. Will the files be available?
Yes, as soon as i gain access to edit my project, for some reason i did not get the invitation email to edit it, and the immediate link landed on a 404.
> [@blurfl](#):
>
> That’s the same as the CommunityGarden version then. 👍 Note that the firmware identifies the TLE5206 board as “PCB v1.3 TLE5206 Detected” in GC (for historical reasons pcbVersion is the strapped value minus 1).
I’ve been out for business for the past three weeks, just posted from the top of my head, will confirm that when i get back, it does get identified and passes test, also work as it should.
> [@blurfl](#):
>
> It surprised me that the AUX functions weren’t implemented. Can you share the reasoning?
We haven’t had time to test or implement aux functions yet, we’ll include it in future versions.
---
### Author:  [@blurfl](https://forums.maslowcnc.com/u/blurfl)
#### Post date: [November 7, 2018, 6:25pm UTC](https://forums.maslowcnc.com/t/maslow-kits-for-sale-soon/7581/10 "2018-11-07T18:25:36Z")
> [@2cents](#):
>
> it does get identified and passes test, also work as it should.
One thing I’m interested to check on the schematic is whether gpio pins 33 & 34 are left unattached as in the CommunityGarden TLE5206 design, or are grounded as they were in the stock PowerControl boards. Those pins are needed for SPI functions and were kept free for that purpose.
---
### Author:  [@2cents](https://forums.maslowcnc.com/u/2cents)
#### Post date: [November 8, 2018, 8:59pm UTC](https://forums.maslowcnc.com/t/maslow-kits-for-sale-soon/7581/11 "2018-11-08T20:59:56Z")
> [@blurfl](#):
>
> One thing I’m interested to check on the schematic is whether gpio pins 33 & 34 are left unattached
They were left unattached as in the CommunityGarden TLE5206 design.
Please see pic #3 from the link below.
[https://www.eastbaysource.com/products/power-control-shield-based-on-the-tle5206-h-bridge-from-infineon-technologies](https://www.eastbaysource.com/products/power-control-shield-based-on-the-tle5206-h-bridge-from-infineon-technologies)
Can you please give me a pointer on how regain access to my project so i can edit it? should i post an other project and see if it works this time?
---
### Author:  [@blurfl](https://forums.maslowcnc.com/u/blurfl)
#### Post date: [November 8, 2018, 10:30pm UTC](https://forums.maslowcnc.com/t/maslow-kits-for-sale-soon/7581/12 "2018-11-08T22:30:07Z")
> [@2cents](#):
>
> Please see pic #3 from the link below.
Unattached is the good condition 👍🏻.
The pins in question are two of the group of four in the upper left corner - the two pins closest to the checkmark.
---
### Author:  [@2cents](https://forums.maslowcnc.com/u/2cents)
#### Post date: [November 9, 2018, 4:29pm UTC](https://forums.maslowcnc.com/t/maslow-kits-for-sale-soon/7581/13 "2018-11-09T16:29:22Z")
33/34 NOT grounded (#52/#53).