# Maslow Z axis not moving using controls on web control

**URL:** <https://forums.maslowcnc.com/t/maslow-z-axis-not-moving-using-controls-on-web-control/16186>\
**Category:** Troubleshooting\
**Created:** [February 24, 2021, 11:21pm UTC](https://forums.maslowcnc.com/t/maslow-z-axis-not-moving-using-controls-on-web-control/16186 "2021-02-24T23:21:16Z")\
**Posts on this page:** 6\
**Page:** 1

<div class="post-metadata">

**Author:** ![scott5620](https://avatars.discourse-cdn.com/v4/letter/s/898d66/32.png) [@scott5620](https://forums.maslowcnc.com/u/scott5620)\
**Post date:** [February 24, 2021, 11:21pm UTC](https://forums.maslowcnc.com/t/maslow-z-axis-not-moving-using-controls-on-web-control/16186/1 "2021-02-24T23:21:16Z")

</div>

Hello All

Newbie with a new toy. Still in the setup phase. Z axis does not move when selecting up or down on web control. Cable and motor are good (have movement when connected to x axis of control module). Diagnostics does not fail anything. Original setup came with ground control and all worked, Upgraded to web control and haven’t been able to operate Z axis to this point. Control module buzzes when trying to move using web control. Any pointers in what I should look for next would be appreciated.  
Windows 10  
WEB CONTROL

Don’t have the other info at this time because I’m not around the machine.

---

<div class="post-metadata">

**Author:** ![scott5620](https://avatars.discourse-cdn.com/v4/letter/s/898d66/32.png) [@scott5620](https://forums.maslowcnc.com/u/scott5620)\
**Post date:** [February 24, 2021, 11:27pm UTC](https://forums.maslowcnc.com/t/maslow-z-axis-not-moving-using-controls-on-web-control/16186/2 "2021-02-24T23:27:30Z")

</div>

Also  
X and y work great. Almost have all the error out using triangular calibration method.

---

<div class="post-metadata">

**Author:** ![Orob](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/orob/32/16344_2.png) [@Orob](https://forums.maslowcnc.com/u/Orob)\
**Post date:** [February 25, 2021, 12:25am UTC](https://forums.maslowcnc.com/t/maslow-z-axis-not-moving-using-controls-on-web-control/16186/3 "2021-02-25T00:25:18Z")

</div>

go into the settings and check if the z axis is enabled. it is a toggle on/off switch

---

<div class="post-metadata">

**Author:** ![scott5620](https://avatars.discourse-cdn.com/v4/letter/s/898d66/32.png) [@scott5620](https://forums.maslowcnc.com/u/scott5620)\
**Post date:** [February 25, 2021, 1:17am UTC](https://forums.maslowcnc.com/t/maslow-z-axis-not-moving-using-controls-on-web-control/16186/4 "2021-02-25T01:17:02Z")

</div>

It is enabled

---

<div class="post-metadata">

**Author:** ![scott5620](https://avatars.discourse-cdn.com/v4/letter/s/898d66/32.png) [@scott5620](https://forums.maslowcnc.com/u/scott5620)\
**Post date:** [February 25, 2021, 5:27pm UTC](https://forums.maslowcnc.com/t/maslow-z-axis-not-moving-using-controls-on-web-control/16186/5 "2021-02-25T17:27:14Z")

</div>

Thanks Orob for the assistance. I was able to clear problem by going back to ground control. When everything was working in ground control I was able to successfully return to web control with all motor function.

---

<div class="post-metadata">

**Author:** ![Orob](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/orob/32/16344_2.png) [@Orob](https://forums.maslowcnc.com/u/Orob)\
**Post date:** [February 25, 2021, 8:53pm UTC](https://forums.maslowcnc.com/t/maslow-z-axis-not-moving-using-controls-on-web-control/16186/6 "2021-02-25T20:53:02Z")

</div>

Glad you were able to figure it out.