# Nothing happens when power is plugged in 4.1 New Build

**URL:** <https://forums.maslowcnc.com/t/nothing-happens-when-power-is-plugged-in-4-1-new-build/23813>\
**Category:** Troubleshooting\
**Tags:** firmware, assembly\
**Created:** [April 18, 2025, 5:31pm UTC](https://forums.maslowcnc.com/t/nothing-happens-when-power-is-plugged-in-4-1-new-build/23813 "2025-04-18T17:31:48Z")\
**Posts on this page:** 12\
**Page:** 1

<div class="post-metadata">

**Author:** ![Koz](https://avatars.discourse-cdn.com/v4/letter/k/7ea924/32.png) [@Koz](https://forums.maslowcnc.com/u/Koz)\
**Post date:** [April 18, 2025, 5:31pm UTC](https://forums.maslowcnc.com/t/nothing-happens-when-power-is-plugged-in-4-1-new-build/23813/1 "2025-04-18T17:31:48Z")

</div>

Hello,

I just finished assembling my 4.1 and nothing happens when the power is plugged in. The fan doesn’t start, no LEDs light up, the WIFI network doesn’t start up, and it doesn’t show up on my computer when plugged in via USB.

The board is definitely receiving power as the components heat up. the heat is slow and on par with what i would expect for un cooled components. No smoke, No obvious shorts or hot spots.

Is it possible i just have a bad board?

---

<div class="post-metadata">

**Author:** ![bar](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/bar/32/10_2.png) [@bar](https://forums.maslowcnc.com/u/bar)\
**Post date:** [April 18, 2025, 5:53pm UTC](https://forums.maslowcnc.com/t/nothing-happens-when-power-is-plugged-in-4-1-new-build/23813/2 "2025-04-18T17:53:56Z")

</div>

There is no green LED? The green LED should be tied directly to the power supply so if the board is getting power I would expect that one to come on pretty much no matter what else is happening on the board

---

<div class="post-metadata">

**Author:** ![Koz](https://avatars.discourse-cdn.com/v4/letter/k/7ea924/32.png) [@Koz](https://forums.maslowcnc.com/u/Koz)\
**Post date:** [April 18, 2025, 5:57pm UTC](https://forums.maslowcnc.com/t/nothing-happens-when-power-is-plugged-in-4-1-new-build/23813/3 "2025-04-18T17:57:55Z")

</div>

Nope no led at all. 😕

Just a little bit of heat on the components near the plug.

---

<div class="post-metadata">

**Author:** ![bar](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/bar/32/10_2.png) [@bar](https://forums.maslowcnc.com/u/bar)\
**Post date:** [April 18, 2025, 5:59pm UTC](https://forums.maslowcnc.com/t/nothing-happens-when-power-is-plugged-in-4-1-new-build/23813/4 "2025-04-18T17:59:21Z")

</div>

Hmmm that could be a board issue or a power supply issue. I’ve just never seen a board fail in that way before

Can you try plugging it into a different outlet?

---

<div class="post-metadata">

**Author:** ![Koz](https://avatars.discourse-cdn.com/v4/letter/k/7ea924/32.png) [@Koz](https://forums.maslowcnc.com/u/Koz)\
**Post date:** [April 18, 2025, 6:07pm UTC](https://forums.maslowcnc.com/t/nothing-happens-when-power-is-plugged-in-4-1-new-build/23813/5 "2025-04-18T18:07:17Z")

</div>

Same result on another outlet, no LED, No fan but if I leave it plugged in for about a minute it warms up near the plug.

---

<div class="post-metadata">

**Author:** ![bar](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/bar/32/10_2.png) [@bar](https://forums.maslowcnc.com/u/bar)\
**Post date:** [April 18, 2025, 6:27pm UTC](https://forums.maslowcnc.com/t/nothing-happens-when-power-is-plugged-in-4-1-new-build/23813/6 "2025-04-18T18:27:11Z")

</div>

That is very strange. It getting warm would indicate that the power supply is working, but it not having a green LED makes me think that the power supply isn’t working.

---

<div class="post-metadata">

**Author:** ![bar](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/bar/32/10_2.png) [@bar](https://forums.maslowcnc.com/u/bar)\
**Post date:** [April 18, 2025, 6:27pm UTC](https://forums.maslowcnc.com/t/nothing-happens-when-power-is-plugged-in-4-1-new-build/23813/7 "2025-04-18T18:27:44Z")

</div>

You don’t see it creating a “Maslow” wifi network, right?

---

<div class="post-metadata">

**Author:** ![Koz](https://avatars.discourse-cdn.com/v4/letter/k/7ea924/32.png) [@Koz](https://forums.maslowcnc.com/u/Koz)\
**Post date:** [April 18, 2025, 6:29pm UTC](https://forums.maslowcnc.com/t/nothing-happens-when-power-is-plugged-in-4-1-new-build/23813/8 "2025-04-18T18:29:50Z")

</div>

Correct. No WIFI network. I’ve only left it plugged in for a bout a minute as I wanted to avoid damaging the board by letting it overheat. If it would need to be plugged in longer than that I can try it.

---

<div class="post-metadata">

**Author:** ![Koz](https://avatars.discourse-cdn.com/v4/letter/k/7ea924/32.png) [@Koz](https://forums.maslowcnc.com/u/Koz)\
**Post date:** [April 18, 2025, 6:31pm UTC](https://forums.maslowcnc.com/t/nothing-happens-when-power-is-plugged-in-4-1-new-build/23813/9 "2025-04-18T18:31:16Z")

</div>

Power supply reads a stable 24.2V on a multimeter under no load.

---

<div class="post-metadata">

**Author:** ![bar](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/bar/32/10_2.png) [@bar](https://forums.maslowcnc.com/u/bar)\
**Post date:** [April 18, 2025, 6:35pm UTC](https://forums.maslowcnc.com/t/nothing-happens-when-power-is-plugged-in-4-1-new-build/23813/10 "2025-04-18T18:35:27Z")

</div>

Excellent test, OK it sounds like the board for sure! Great testing!

I will DM you a code for a replacement right now!

---

<div class="post-metadata">

**Author:** ![Koz](https://avatars.discourse-cdn.com/v4/letter/k/7ea924/32.png) [@Koz](https://forums.maslowcnc.com/u/Koz)\
**Post date:** [April 18, 2025, 6:38pm UTC](https://forums.maslowcnc.com/t/nothing-happens-when-power-is-plugged-in-4-1-new-build/23813/11 "2025-04-18T18:38:53Z")

</div>

Great Thank you!

---

<div class="post-metadata">

**Author:** ![Koz](https://avatars.discourse-cdn.com/v4/letter/k/7ea924/32.png) [@Koz](https://forums.maslowcnc.com/u/Koz)\
**Post date:** [April 23, 2025, 12:05am UTC](https://forums.maslowcnc.com/t/nothing-happens-when-power-is-plugged-in-4-1-new-build/23813/12 "2025-04-23T00:05:00Z")

</div>

The control board was NOT the problem.

If you are having similar issues see my other post here:

> [@Solution for disconnect and board wont start problem!](https://forums.maslowcnc.com/t/solution-for-disconnect-and-board-wont-start-problem/23871):
>
> Hello all, TLDR: Clip the thru pins on the encoders JST-HX headers. It will save your headaches. I had an issue after initial assembly where my control board didn’t indicate it had power even when plugged in. Power supply was fine and some of the components got hot but it wouldn’t start up. Thinking it was a control board issue after troubleshooting I received a replacement board and i checked it before assembly and it started up just fine. After installation I plugged in the power and… Nothin…
