# Please add to the not shop **URL:** \ **Category:** Uncategorized\ **Created:** [July 23, 2025, 10:50pm UTC](https://forums.maslowcnc.com/t/please-add-to-the-not-shop/24604 "2025-07-23T22:50:15Z")\ **Posts on this page:** 11\ **Page:** 1
**Author:** ![dlang](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/dlang/32/859_2.png) [@dlang](https://forums.maslowcnc.com/u/dlang)\ **Post date:** [July 23, 2025, 10:50pm UTC](https://forums.maslowcnc.com/t/please-add-to-the-not-shop/24604/1 "2025-07-23T22:50:15Z")
the router-b-gone items in > [@M4 Router Be Gone (installed the spindle)](https://forums.maslowcnc.com/t/m4-router-be-gone-installed-the-spindle/21389/20): > > @md8n would you mind sharing the housing stls? It’s a 52mm spindle you are using? the outer sleeve in > [@M4 Router Be Gone (installed the spindle)](https://forums.maslowcnc.com/t/m4-router-be-gone-installed-the-spindle/21389/67): > > Report on the Outer Sleeve So I noticed that there seemed to be more play, than what I would like, between the arms and the outer sleeve. Today one of the arms was jamming up, so I needed to pull the machine apart to sort it out, and that seemed like an ideal time to check out the outer sleeve as well. Here’s how it looks From the top That ‘dirty’ patch is where the top clamp presses against it. From the bottom The compression indicated wit… the wedge in > [@M4 Router Be Gone (installed the spindle)](https://forums.maslowcnc.com/t/m4-router-be-gone-installed-the-spindle/21389/85): > > New clamp wedge design. Remember to set a pause in your 3D printer at the layer height at the top of the captive nut. And as soon as your printer hits that pause layer get the captive nuts in pronto - it’s easier when the plastic is hot, and you’ll get better layer adhesion when you continue printing. [ClampWedgeV3.stp](https://forums.maslowcnc.com/uploads/short-url/65jlmD42Ll1dYhgder737VMCRsY.stp) (482.0 KB) the mounts in [M4 Router Mounter Be-Gone (use any router with a side entry cord) - #34 by NKT](https://forums.maslowcnc.com/t/m4-router-mounter-be-gone-use-any-router-with-a-side-entry-cord/21202/34) printed belt end exported from [Onshape](https://cad.onshape.com/documents/764e57e1318b9953e5986480/w/d0fb021f278db7c3ec637c49/e/02bcc0a7b413effebd47b49f) (possibly with a couple different hole sizes) top clamp exported from [Onshape](https://cad.onshape.com/documents/764e57e1318b9953e5986480/w/d0fb021f278db7c3ec637c49/e/0f11c66e8ca055216ebc117f) belt ends exported from [Onshape](https://cad.onshape.com/documents/764e57e1318b9953e5986480/w/d0fb021f278db7c3ec637c49/e/02bcc0a7b413effebd47b49f) corner pieces exported from > **[Onshape](https://cad.onshape.com/documents/764e57e1318b9953e5986480/w/d0fb021f278db7c3ec637c49/e/02bcc0a7b413effebd47b49f)** > > Sign in to Onshape, the #1 fastest growing CAD system in the world. ---
**Author:** ![bar](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/bar/32/10_2.png) [@bar](https://forums.maslowcnc.com/u/bar)\ **Post date:** [July 23, 2025, 11:22pm UTC](https://forums.maslowcnc.com/t/please-add-to-the-not-shop/24604/2 "2025-07-23T23:22:48Z")
I feel like we maybe need to come up with a better system for sharing CAD files. Maybe another page? ---
**Author:** ![Carson\_Barry](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/carson_barry/32/23367_2.png) [@Carson\_Barry](https://forums.maslowcnc.com/u/Carson_Barry)\ **Post date:** [July 24, 2025, 2:43pm UTC](https://forums.maslowcnc.com/t/please-add-to-the-not-shop/24604/3 "2025-07-24T14:43:01Z")
Might be valuable to put it in the repo instead of on the site or on the forum, so it could be in markdown, formatted similar to the current not shop, could be added to by anyone (just needing approval for changes to go live), and would be easy to just re-route the current nav on the site to redirect there instead so all old links just work and nothing is truly deprecated other than the old page file itself. Would also be a good way for creators to be able to update their own files if they redesign them. Onshape files could just be links in the markdown, but people that don’t use OnShape could just upload the files themselves in a designated directory and link to the relevant file(s)/folder in that markdown file. ---
**Author:** ![dlang](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/dlang/32/859_2.png) [@dlang](https://forums.maslowcnc.com/u/dlang)\ **Post date:** [July 24, 2025, 6:47pm UTC](https://forums.maslowcnc.com/t/please-add-to-the-not-shop/24604/4 "2025-07-24T18:47:13Z")
Bar wrote: > I feel like we maybe need to come up with a better system for sharing CAD > files. Maybe another page? There is sharing cad files, and there is sharing links to onshape where the cad can have config options for example, the belt end and corners can be configured for any size pin and to be different lengths. I was thinking that the default pin size and length could be exported to a stl and directly linked on the not shop page and then a link to the onshape doc with a note that if you need different versions, go there, set the config variables and export the parts may need to have a video about that. David Lang ---
**Author:** ![bar](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/bar/32/10_2.png) [@bar](https://forums.maslowcnc.com/u/bar)\ **Post date:** [July 24, 2025, 9:08pm UTC](https://forums.maslowcnc.com/t/please-add-to-the-not-shop/24604/5 "2025-07-24T21:08:42Z")
Ideally I’d like to be able to share them through abundance 😀 ---
**Author:** ![Carson\_Barry](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/carson_barry/32/23367_2.png) [@Carson\_Barry](https://forums.maslowcnc.com/u/Carson_Barry)\ **Post date:** [July 24, 2025, 9:15pm UTC](https://forums.maslowcnc.com/t/please-add-to-the-not-shop/24604/6 "2025-07-24T21:15:46Z")
I think I can see where you’re coming from, I haven’t had a chance to look into that and just lack a lot of context. I’ll admit, I’m likely not liable to use it because I have Aspire workflows already and am enjoying the bells and whistles (and just got done teaching it to my dad, lol). Would be nice if users didn’t have to learn/install/use an additional tool just to access files, especially if they aren’t already using OnShape and have to now add two new bits of software to their stack instead of just the one (Onshape). ---
**Author:** ![bar](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/bar/32/10_2.png) [@bar](https://forums.maslowcnc.com/u/bar)\ **Post date:** [July 24, 2025, 9:57pm UTC](https://forums.maslowcnc.com/t/please-add-to-the-not-shop/24604/7 "2025-07-24T21:57:15Z")
Ideally we could share things like this: [https://abundance.maslowcnc.com/run/BarbourSmith/Pipe-Flange](https://abundance.maslowcnc.com/run/BarbourSmith/Pipe-Flange) That way folks could customize them a little bit without needing to log in or learn any new software. In that example you can adjust the length of the pipe and export it as a .stl file without needing to learn much ---
**Author:** ![dlang](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/dlang/32/859_2.png) [@dlang](https://forums.maslowcnc.com/u/dlang)\ **Post date:** [July 24, 2025, 10:13pm UTC](https://forums.maslowcnc.com/t/please-add-to-the-not-shop/24604/8 "2025-07-24T22:13:42Z")
Bar wrote: > Ideally I’d like to be able to share them through abundance 😀 that will have exactly the same issues as sharing onshape docs (the designs are live elsewhere, not static files) David Lang ---
**Author:** ![dlang](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/dlang/32/859_2.png) [@dlang](https://forums.maslowcnc.com/u/dlang)\ **Post date:** [July 24, 2025, 10:24pm UTC](https://forums.maslowcnc.com/t/please-add-to-the-not-shop/24604/9 "2025-07-24T22:24:12Z")
onshape can do the same thing with config options. see > **[Onshape](https://cad.onshape.com/documents/764e57e1318b9953e5986480/w/d0fb021f278db7c3ec637c49/e/02bcc0a7b413effebd47b49f)** > > Sign in to Onshape, the #1 fastest growing CAD system in the world with over 4 million users. it lets you set the board size , bolt size, thickness of belt end (and probably way too many other options) and then export the stl without logging in or needing to learn how to do any design work in onshape. David Lang ---
**Author:** ![dlang](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/dlang/32/859_2.png) [@dlang](https://forums.maslowcnc.com/u/dlang)\ **Post date:** [July 24, 2025, 10:42pm UTC](https://forums.maslowcnc.com/t/please-add-to-the-not-shop/24604/10 "2025-07-24T22:42:03Z")
another example would be the spindle holder I’m in the middle of designing (based on router-b-gone) > **[Onshape](https://cad.onshape.com/documents/764e57e1318b9953e5986480/w/d0fb021f278db7c3ec637c49/e/f4c84f7f71db5145c406defd)** > > Sign in to Onshape, the #1 fastest growing CAD system in the world with over 4 million users. it lets you set the thickness of some parts and select the spindle type from a dropdown and adjusts everything to fit David Lang ---
**Author:** ![dlang](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/dlang/32/859_2.png) [@dlang](https://forums.maslowcnc.com/u/dlang)\ **Post date:** [August 5, 2025, 1:28am UTC](https://forums.maslowcnc.com/t/please-add-to-the-not-shop/24604/11 "2025-08-05T01:28:09Z")
also add [Maslow CnC Assembly Tools](https://forums.maslowcnc.com/t/maslow-cnc-assembly-tools/24656)