# Question on using multiple sleds

**URL:** <https://forums.maslowcnc.com/t/question-on-using-multiple-sleds/5338>\
**Category:** No Judgement\
**Created:** [July 31, 2018, 9:15pm UTC](https://forums.maslowcnc.com/t/question-on-using-multiple-sleds/5338 "2018-07-31T21:15:29Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![DakotaJim](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/dakotajim/32/7581_2.png) [@DakotaJim](https://forums.maslowcnc.com/u/DakotaJim)\
**Post date:** [July 31, 2018, 9:15pm UTC](https://forums.maslowcnc.com/t/question-on-using-multiple-sleds/5338/1 "2018-07-31T21:15:29Z")

</div>

Ok, I was thinking that having a second sled with dremel or trim router set up for 1/8 bits for fine detail would be a good idea. Seeing as how I just purchased a ring kit on ebay from Joel I decided maybe I should ask some questions and see if the group could answer them.

A. Having 2 sleds with the same ring system should result in not needing to recalibrate the x & y every time I switch sleds? Right? (please be right)

1. Do both sleds need to be the same weight for question a to be true?

C. And what is the ultimate answer?

Thanks for any input.

---

<div class="post-metadata">

**Author:** ![blurfl](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/blurfl/32/9_2.png) [@blurfl](https://forums.maslowcnc.com/u/blurfl)\
**Post date:** [July 31, 2018, 9:35pm UTC](https://forums.maslowcnc.com/t/question-on-using-multiple-sleds/5338/2 "2018-07-31T21:35:22Z")

</div>

> [@DakotaJim](#):
>
> Do both sleds need to be the same weight for question a to be true?

I think this would be best. Having as much as possible the same would be the goal. Having the same linkage - ring or parallelogram would help a lot.

---

<div class="post-metadata">

**Author:** ![Bee](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/bee/32/2160_2.png) [@Bee](https://forums.maslowcnc.com/u/Bee)\
**Post date:** [July 31, 2018, 10:14pm UTC](https://forums.maslowcnc.com/t/question-on-using-multiple-sleds/5338/3 "2018-07-31T22:14:44Z")

</div>

I’m going to point out your workflow and zero point need to be spot on or you end up with “ghosting” if things are out of alignment. With that in mind I would design a non critical feature to check the alignment with a fake tool change after it. It is a verification check point. If the alignment was ok continue if not try again. I would make it 5 small spots so I have more then 1 try. Just 2 minutes of free thinking on this while filling out other information in a ticketing system.

hope that helps

Thank you

---

<div class="post-metadata">

**Author:** ![blurfl](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/blurfl/32/9_2.png) [@blurfl](https://forums.maslowcnc.com/u/blurfl)\
**Post date:** [July 31, 2018, 11:01pm UTC](https://forums.maslowcnc.com/t/question-on-using-multiple-sleds/5338/4 "2018-07-31T23:01:24Z")

</div>

> [@DakotaJim](#):
>
> having a second sled with dremel or trim router set up for 1/8 bits for fine detail would be a good idea.

How about an adapter to hold the dremel in the router base in place of the router motor? It would need to weigh the same as the router motor, but would be simpler than getting another ring and z-axis kit.

---

<div class="post-metadata">

**Author:** ![dlang](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/dlang/32/859_2.png) [@dlang](https://forums.maslowcnc.com/u/dlang)\
**Post date:** [August 5, 2018, 11:41pm UTC](https://forums.maslowcnc.com/t/question-on-using-multiple-sleds/5338/5 "2018-08-05T23:41:16Z")

</div>

As long as both sleds are the same weight and have the same rotation radius, you  
can avoid recalibrating.

In practice, this is almost never going to be the case, it would be a nice idea  
to have the maslow store a couple different sets of calibration and let you  
switch between them. This should not be that hard to do.
