# Select-deselect a specific Dogbone

**URL:** <https://forums.maslowcnc.com/t/select-deselect-a-specific-dogbone/23651>\
**Category:** Uncategorized\
**Tags:** krabzcam\
**Created:** [March 31, 2025, 7:06pm UTC](https://forums.maslowcnc.com/t/select-deselect-a-specific-dogbone/23651 "2025-03-31T19:06:04Z")\
**Posts on this page:** 8\
**Page:** 1

<div class="post-metadata">

**Author:** ![Betalombo](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/betalombo/32/26664_2.png) [@Betalombo](https://forums.maslowcnc.com/u/Betalombo)\
**Post date:** [March 31, 2025, 7:06pm UTC](https://forums.maslowcnc.com/t/select-deselect-a-specific-dogbone/23651/1 "2025-03-31T19:06:04Z")

</div>

One of the features I like most about Krabzcam is the ability to add dogbones, but I’m working on a project that has several angles I wish weren’t taken so seriously. Does Krabzcam have a feature that allows me to deselect a specific dogbone?

---

<div class="post-metadata">

**Author:** ![mkrabset](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/mkrabset/32/16092_2.png) [@mkrabset](https://forums.maslowcnc.com/u/mkrabset)\
**Post date:** [April 8, 2025, 9:00pm UTC](https://forums.maslowcnc.com/t/select-deselect-a-specific-dogbone/23651/2 "2025-04-08T21:00:54Z")

</div>

Hi, this is currently not possible in KrabzCAM.  
I’ll consider adding some kind of feature for this, but no promises.  
Maybe it would help if there was a configurable max-angle for dogbones, so that corners ‘more obtuse’ than this angle gets ignored? Or maybe both a min and a max angle?

-M

---

<div class="post-metadata">

**Author:** ![dlang](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/dlang/32/859_2.png) [@dlang](https://forums.maslowcnc.com/u/dlang)\
**Post date:** [April 8, 2025, 9:14pm UTC](https://forums.maslowcnc.com/t/select-deselect-a-specific-dogbone/23651/3 "2025-04-08T21:14:28Z")

</div>

Marius Krabset wrote:

> Hi, this is currently not possible in KrabzCAM.  
> I’ll consider adding some kind of feature for this, but no promises.  
> Maybe it would help if there was a configurable max-angle for dogbones, so that corners ‘more obtuse’ than this angle gets ignored? Or maybe both a min and a max angle?

I’m not familiar with KrabzCAM, but do your dogbones put the center of the  
cutter on one (or both) of the lines into the angle? or does it go in diagonally  
at 1/2 the angle until the edge of the cutter hits the angle?

too many dogbone tools do the former, which leaves much larger gaps.

David Lang

---

<div class="post-metadata">

**Author:** ![Betalombo](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/betalombo/32/26664_2.png) [@Betalombo](https://forums.maslowcnc.com/u/Betalombo)\
**Post date:** [April 9, 2025, 3:32pm UTC](https://forums.maslowcnc.com/t/select-deselect-a-specific-dogbone/23651/4 "2025-04-09T15:32:48Z")

</div>

> [@mkrabset](#):
>
> Or maybe both a min and a max angle?

that would be very good

---

<div class="post-metadata">

**Author:** ![mkrabset](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/mkrabset/32/16092_2.png) [@mkrabset](https://forums.maslowcnc.com/u/mkrabset)\
**Post date:** [April 9, 2025, 5:47pm UTC](https://forums.maslowcnc.com/t/select-deselect-a-specific-dogbone/23651/5 "2025-04-09T17:47:19Z")

</div>

@Betalombo I’ve added min/max angle parameters for dogbones. (become visible when dogbones are enabled).  
Try it out and please let me know of any issues.

-M

---

<div class="post-metadata">

**Author:** ![mkrabset](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/mkrabset/32/16092_2.png) [@mkrabset](https://forums.maslowcnc.com/u/mkrabset)\
**Post date:** [April 9, 2025, 5:51pm UTC](https://forums.maslowcnc.com/t/select-deselect-a-specific-dogbone/23651/6 "2025-04-09T17:51:38Z")

</div>

@dlang KrabzCAM generates dogbone paths that approaches the corner from the center, like this:

 ![image](https://canada1.discourse-cdn.com/flex031/uploads/maslowcnc/original/3X/8/2/8209295fb71a0cc2dd5385f93b81c9345af4e916.png)

---

<div class="post-metadata">

**Author:** ![dlang](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/dlang/32/859_2.png) [@dlang](https://forums.maslowcnc.com/u/dlang)\
**Post date:** [April 9, 2025, 6:42pm UTC](https://forums.maslowcnc.com/t/select-deselect-a-specific-dogbone/23651/7 "2025-04-09T18:42:14Z")

</div>

Marius Krabset wrote:

> @dlang KrabzCAM generates dogbone paths that approaches the corner from the center, like this:

thanks, that’s what I was hoping for.

David Lang

---

<div class="post-metadata">

**Author:** ![Betalombo](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/betalombo/32/26664_2.png) [@Betalombo](https://forums.maslowcnc.com/u/Betalombo)\
**Post date:** [April 9, 2025, 11:43pm UTC](https://forums.maslowcnc.com/t/select-deselect-a-specific-dogbone/23651/8 "2025-04-09T23:43:35Z")

</div>

![Captura de pantalla 2025-04-09 183133](https://canada1.discourse-cdn.com/flex031/uploads/maslowcnc/original/3X/8/b/8b99f377e33fc03faa385462f491d4de06676942.png)  
Thank you very much, I had an angle very close to 90 degrees that I did not want to affect and it worked wonderfully
