# Setup Configuration Dialog Box Looks Different

**URL:** <https://forums.maslowcnc.com/t/setup-configuration-dialog-box-looks-different/23924>\
**Category:** Software\
**Created:** [April 27, 2025, 1:44pm UTC](https://forums.maslowcnc.com/t/setup-configuration-dialog-box-looks-different/23924 "2025-04-27T13:44:57Z")\
**Posts on this page:** 3\
**Page:** 1

<div class="post-metadata">

**Author:** ![StevieP](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/steviep/32/28107_2.png) [@StevieP](https://forums.maslowcnc.com/u/StevieP)\
**Post date:** [April 27, 2025, 1:44pm UTC](https://forums.maslowcnc.com/t/setup-configuration-dialog-box-looks-different/23924/1 "2025-04-27T13:44:57Z")

</div>

After assembling my Maslow 4.1 I started following the calibration instructions and the Setup Config dialog box looks different, the instructions (and video) have a field to fill in machine height and machine width dimensions whereas what I assume is an un updated interface for the newer version of the firmware only wants the Extend Dist. What dimension is that referring to?  
I also see there is a field for both Retraction and Calibration Force now.  
Are there any updated instructions or notes that are issued when new versions of the Firmware are made available?  
Regards  
Steve

---

<div class="post-metadata">

**Author:** ![dlang](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/dlang/32/859_2.png) [@dlang](https://forums.maslowcnc.com/u/dlang)\
**Post date:** [April 27, 2025, 2:31pm UTC](https://forums.maslowcnc.com/t/setup-configuration-dialog-box-looks-different/23924/2 "2025-04-27T14:31:09Z")

</div>

Steve Pennell wrote:

> After assembling my Maslow 4.1 I started following the calibration instructions and the Setup Config dialog box looks different, the instructions (and video) have a field to fill in machine height and machine width dimensions whereas what I assume is an un updated interface for the newer version of the firmware only wants the Extend Dist. What dimension is that referring to?

This is just a distance of how much belt to feed out (center to corner), the  
default will work for a 8x10 frame, just make it bigger until the belts reach

> I also see there is a field for both Retraction and Calibration Force now.  
> Are there any updated instructions or notes that are issued when new versions of the Firmware are made available?

not in once place yet (look at the 1.0 instructions), Bar has been focusing on  
getting the kits shipped out and beating the tariff hikes, he is planning to  
work on the updated instructions in the next week or so.

David Lang

---

<div class="post-metadata">

**Author:** ![bar](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/bar/32/10_2.png) [@bar](https://forums.maslowcnc.com/u/bar)\
**Post date:** [April 28, 2025, 8:28pm UTC](https://forums.maslowcnc.com/t/setup-configuration-dialog-box-looks-different/23924/3 "2025-04-28T20:28:57Z")

</div>

> [@StevieP](#):
>
> Are there any updated instructions or notes that are issued when new versions of the Firmware are made available?

I am working on that right now! The way things look is going to get updated again in this weeks firmware update and there will be a new video and instructions to go along with the update. They should be out this week!