# Setup -jog for z axis

**URL:** <https://forums.maslowcnc.com/t/setup-jog-for-z-axis/13932>\
**Category:** Feature Request / Development\
**Created:** [July 8, 2020, 8:08pm UTC](https://forums.maslowcnc.com/t/setup-jog-for-z-axis/13932 "2020-07-08T20:08:56Z")\
**Posts on this page:** 8\
**Page:** 1

<div class="post-metadata">

**Author:** ![RTrim](https://avatars.discourse-cdn.com/v4/letter/r/dec6dc/32.png) [@RTrim](https://forums.maslowcnc.com/u/RTrim)\
**Post date:** [July 8, 2020, 8:08pm UTC](https://forums.maslowcnc.com/t/setup-jog-for-z-axis/13932/1 "2020-07-08T20:08:56Z")

</div>

The “jog controls” for left and right motors. Can we also duplicate this for the Z axis?

Two drivers behind this:

1. I lost yesterday to a strange z anomoly. It took a long sleep to deduce that I had broken a wire connector. The z motor moved 360 when i clicked “test motors” . It then moved 20mm hesitantly, regardless of how far it was asked to move.  
However, when attached to the right motor socket I could run a different test - the motor also turned 360 when I asked for 10 degrees.

2. using this Jerry rigged single.motor controller i can to turn the shaft 360 a couple of times - working out the Z calibration was then child’s play.

---

<div class="post-metadata">

**Author:** ![Orob](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/orob/32/16344_2.png) [@Orob](https://forums.maslowcnc.com/u/Orob)\
**Post date:** [July 9, 2020, 12:53am UTC](https://forums.maslowcnc.com/t/setup-jog-for-z-axis/13932/2 "2020-07-09T00:53:15Z")

</div>

the z axis jog buttons in webcontrol are in the z axis menu.

---

<div class="post-metadata">

**Author:** ![RTrim](https://avatars.discourse-cdn.com/v4/letter/r/dec6dc/32.png) [@RTrim](https://forums.maslowcnc.com/u/RTrim)\
**Post date:** [July 9, 2020, 8:55am UTC](https://forums.maslowcnc.com/t/setup-jog-for-z-axis/13932/3 "2020-07-09T08:55:06Z")

</div>

With almost all machines now having a Z-axis it would make more sense to set/wiggle the the Z motor earlier in the setup process.

Thanks Orob, Yes, I had found the Z-axis move and used it in the description above. But this is moving the Z motor after you have set a calibration number for it. (Actually I guess we all set a small number, measure the movemement and then scale. But by this time it is late in the day and we have spent an hour on a forum trying to find the button)

Personally I’d move the Z-calibration number input to just below this as well.

 ![ZSetup](https://canada1.discourse-cdn.com/flex031/uploads/maslowcnc/original/3X/f/d/fdfb14bf029b96961b39c87b74178f9178ea27f3.jpeg)

---

<div class="post-metadata">

**Author:** ![Orob](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/orob/32/16344_2.png) [@Orob](https://forums.maslowcnc.com/u/Orob)\
**Post date:** [July 9, 2020, 2:42pm UTC](https://forums.maslowcnc.com/t/setup-jog-for-z-axis/13932/4 "2020-07-09T14:42:07Z")

</div>

Oh, I see what you are asking for. Typically the z axis is not “calibrated” like the chains and you extend the chains and set the sprockets with the sled not attached, which means the z axis at this stage may not even be connected. Once you get the sled on, then you use the regular “post” calibration moves. Setting the z axis is done routinely after tool/bit changes, so it would need to be done often and not buried in the calibration menu. Intuitively, the z axis zero isn’t critical until the chains are ready: definitely before the calibration cuts, but after the chain extension. I would not advocate for a z axis movement button on the set-sprocket page. If you need to move it, do that before you go to the set sprocket page or after.

---

<div class="post-metadata">

**Author:** ![RTrim](https://avatars.discourse-cdn.com/v4/letter/r/dec6dc/32.png) [@RTrim](https://forums.maslowcnc.com/u/RTrim)\
**Post date:** [July 9, 2020, 2:57pm UTC](https://forums.maslowcnc.com/t/setup-jog-for-z-axis/13932/5 "2020-07-09T14:57:53Z")

</div>

The above is what I’ve seen comming cold to the software and the kit. I’m aware that those with running machines would probably not get it.

I used the Z commands to adjust and set the Z home too. They are nicely and logically in mm. There is no request to change these. I’ve not got as far as a bit change yet.

The request is to ADD a manual control to Z movement in the Set sproket menu and having the ability to know the motor is actually working correctly

---

<div class="post-metadata">

**Author:** ![Orob](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/orob/32/16344_2.png) [@Orob](https://forums.maslowcnc.com/u/Orob)\
**Post date:** [July 9, 2020, 9:52pm UTC](https://forums.maslowcnc.com/t/setup-jog-for-z-axis/13932/6 "2020-07-09T21:52:49Z")

</div>

The feature you seek is redundant, but the way it is situated does not appear intuitive to a new user. You are asking for a z setup menu or buttons for checking the z axis in a location that a new user would be more likely to find it earlier in the setup process?

---

<div class="post-metadata">

**Author:** ![talyrath](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/talyrath/32/12810_2.png) [@talyrath](https://forums.maslowcnc.com/u/talyrath)\
**Post date:** [July 9, 2020, 10:28pm UTC](https://forums.maslowcnc.com/t/setup-jog-for-z-axis/13932/7 "2020-07-09T22:28:57Z")

</div>

I think having jog up/down buttons would be less useful than a shortcut that moves the bit to zero and one that moves it to a predefined travel height.

At least those are the two heights I use the most.

---

<div class="post-metadata">

**Author:** ![dlang](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/dlang/32/859_2.png) [@dlang](https://forums.maslowcnc.com/u/dlang)\
**Post date:** [July 10, 2020, 1:39am UTC](https://forums.maslowcnc.com/t/setup-jog-for-z-axis/13932/8 "2020-07-10T01:39:55Z")

</div>

‘test motors’ moves all three motors.

David Lang
