# Sled lifting during small moves or traveling right to left

**URL:** <https://forums.maslowcnc.com/t/sled-lifting-during-small-moves-or-traveling-right-to-left/21023>\
**Category:** Uncategorized\
**Created:** [May 12, 2024, 3:23pm UTC](https://forums.maslowcnc.com/t/sled-lifting-during-small-moves-or-traveling-right-to-left/21023 "2024-05-12T15:23:47Z")\
**Posts on this page:** 9\
**Page:** 1

<div class="post-metadata">

**Author:** ![norelation](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/norelation/32/22331_2.png) [@norelation](https://forums.maslowcnc.com/u/norelation)\
**Post date:** [May 12, 2024, 3:23pm UTC](https://forums.maslowcnc.com/t/sled-lifting-during-small-moves-or-traveling-right-to-left/21023/1 "2024-05-12T15:23:47Z")

</div>

![MaslowLifting](https://canada1.discourse-cdn.com/flex031/uploads/maslowcnc/original/3X/3/8/38c00693bda5c634feb4d3e6223dc334af3a2c9f.gif)  
Seems like the Down Right belt isn’t pulling as tight as the other three which is causing it to lift especially on small moves. Any ideas what could cause this?

---

<div class="post-metadata">

**Author:** ![dlang](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/dlang/32/859_2.png) [@dlang](https://forums.maslowcnc.com/u/dlang)\
**Post date:** [May 12, 2024, 4:11pm UTC](https://forums.maslowcnc.com/t/sled-lifting-during-small-moves-or-traveling-right-to-left/21023/2 "2024-05-12T16:11:50Z")

</div>

That looks like the sled is not sliding as it should, try waxing the bottom of  
the sled to reduce friction.

David Lang

---

<div class="post-metadata">

**Author:** ![bar](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/bar/32/10_2.png) [@bar](https://forums.maslowcnc.com/u/bar)\
**Post date:** [May 13, 2024, 4:16pm UTC](https://forums.maslowcnc.com/t/sled-lifting-during-small-moves-or-traveling-right-to-left/21023/3 "2024-05-13T16:16:46Z")

</div>

I agree with making it slide more, put also giving it a bit more tilt can help push the sled against the wood while cutting

---

<div class="post-metadata">

**Author:** ![jwolter](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/jwolter/32/30787_2.png) [@jwolter](https://forums.maslowcnc.com/u/jwolter)\
**Post date:** [May 14, 2024, 1:49am UTC](https://forums.maslowcnc.com/t/sled-lifting-during-small-moves-or-traveling-right-to-left/21023/4 "2024-05-14T01:49:31Z")

</div>

What angle is your work piece at?

---

<div class="post-metadata">

**Author:** ![HobbyBody](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/hobbybody/32/22894_2.png) [@HobbyBody](https://forums.maslowcnc.com/u/HobbyBody)\
**Post date:** [May 26, 2024, 6:56pm UTC](https://forums.maslowcnc.com/t/sled-lifting-during-small-moves-or-traveling-right-to-left/21023/5 "2024-05-26T18:56:59Z")

</div>

I’m running calibrations and having the same issue. I measure my surface to be 15 Degrees. Any ideas?

---

<div class="post-metadata">

**Author:** ![ronlawrence3](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/ronlawrence3/32/7886_2.png) [@ronlawrence3](https://forums.maslowcnc.com/u/ronlawrence3)\
**Post date:** [May 26, 2024, 7:06pm UTC](https://forums.maslowcnc.com/t/sled-lifting-during-small-moves-or-traveling-right-to-left/21023/6 "2024-05-26T19:06:28Z")

</div>

I found 15 degrees to be not quite enough either and was having the same issue. Fortunately, my frame is basically just leaning against a wall right now so for me I just pulled the bottom out more - probably ~20 degrees or so. I’ll eventually build the bracing for it, but its not sliding at all for me right now just sitting on the concrete in my garage.

---

<div class="post-metadata">

**Author:** ![norelation](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/norelation/32/22331_2.png) [@norelation](https://forums.maslowcnc.com/u/norelation)\
**Post date:** [May 26, 2024, 9:09pm UTC](https://forums.maslowcnc.com/t/sled-lifting-during-small-moves-or-traveling-right-to-left/21023/7 "2024-05-26T21:09:08Z")

</div>

> [@ronlawrence3](#):
>
> nd 15 degrees to be not quite enough either and was having the same issue. Fort

Roughly 20 degrees. The bottom is out at about 24in from the wall and the top is at 72in from the floor. It definitely helped I also go some food grade wax like what is used on chopping boards to help grease the sled.

---

<div class="post-metadata">

**Author:** ![Carson\_Barry](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/carson_barry/32/23367_2.png) [@Carson\_Barry](https://forums.maslowcnc.com/u/Carson_Barry)\
**Post date:** [May 26, 2024, 9:12pm UTC](https://forums.maslowcnc.com/t/sled-lifting-during-small-moves-or-traveling-right-to-left/21023/8 "2024-05-26T21:12:51Z")

</div>

I remember reading that the max angle was 60 or 70 degrees off horizontal, just can’t remember where. Would expect issues above that.

---

<div class="post-metadata">

**Author:** ![AzaB2C](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/azab2c/32/22286_2.png) [@AzaB2C](https://forums.maslowcnc.com/u/AzaB2C)\
**Post date:** [May 26, 2024, 11:19pm UTC](https://forums.maslowcnc.com/t/sled-lifting-during-small-moves-or-traveling-right-to-left/21023/9 "2024-05-26T23:19:56Z")

</div>

What type of bit and rpm? A new sharp carbide single flute upcut bit with trim router running 10k rpm or slower? With Vac hose attached to help clear away chips (and heat).
