# SVG printout different to Easel GCode -\> WebControl cut out

**URL:** <https://forums.maslowcnc.com/t/svg-printout-different-to-easel-gcode-webcontrol-cut-out/15874>\
**Category:** Troubleshooting\
**Tags:** easel\
**Created:** [January 21, 2021, 10:31pm UTC](https://forums.maslowcnc.com/t/svg-printout-different-to-easel-gcode-webcontrol-cut-out/15874 "2021-01-21T22:31:21Z")\
**Posts on this page:** 3\
**Page:** 1

<div class="post-metadata">

**Author:** ![marie.o](https://avatars.discourse-cdn.com/v4/letter/m/8dc957/32.png) [@marie.o](https://forums.maslowcnc.com/u/marie.o)\
**Post date:** [January 21, 2021, 10:31pm UTC](https://forums.maslowcnc.com/t/svg-printout-different-to-easel-gcode-webcontrol-cut-out/15874/1 "2021-01-21T22:31:21Z")

</div>

I have modeled a window molding in inkscape. Printed it out on a piece of paper, and it fits fairly well. However, when I import the svg to easel and generate the Gcode there, cut it on my maslow, the result is different.

 ![svg2maslow-difference](https://canada1.discourse-cdn.com/flex031/uploads/maslowcnc/original/3X/a/d/ad44098fdeef549d31a068b7a8adcc7aff50b26e.jpeg)

For kicks, I cut out two 50mm squares (one inside, one outside). Measuring them shows that they are very near 50mm (maybe .5 off).

My question is: Does Easel do something strange to my SVG? Or is a maslow acting differently when it comes to cutting curves?  
[Fensterecke.nc](https://forums.maslowcnc.com/uploads/short-url/LQb1LkITduj8N3nMOyOmjmoen9.nc) (9.4 KB)

![Eckstück nach Scan2](https://canada1.discourse-cdn.com/flex031/uploads/maslowcnc/original/3X/a/2/a2e28e9c7570090a01c588635f203891d5bcaa8c.svg)

Any and help is greatly appreciated.

marie.o

---

<div class="post-metadata">

**Author:** ![mkrabset](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/mkrabset/32/16092_2.png) [@mkrabset](https://forums.maslowcnc.com/u/mkrabset)\
**Post date:** [January 21, 2021, 11:54pm UTC](https://forums.maslowcnc.com/t/svg-printout-different-to-easel-gcode-webcontrol-cut-out/15874/2 "2021-01-21T23:54:24Z")

</div>

I think the gcode matches the SVG accurately for an inner profile with tool-diameter of about 6.35mm.  
Calibration issue on the maslow maybe?

-Marius

---

<div class="post-metadata">

**Author:** ![marie.o](https://avatars.discourse-cdn.com/v4/letter/m/8dc957/32.png) [@marie.o](https://forums.maslowcnc.com/u/marie.o)\
**Post date:** [January 22, 2021, 6:24am UTC](https://forums.maslowcnc.com/t/svg-printout-different-to-easel-gcode-webcontrol-cut-out/15874/3 "2021-01-22T06:24:30Z")

</div>

Thank you for the feedback. So Easel is good.

Calibration in general is an issue I know about in my setup, but I wasn’t aware that it is as bad. Especially after trying the squares, I thought that it might be a different issue.