# Thinking of making my first sled out of UHMW plastic

**URL:** <https://forums.maslowcnc.com/t/thinking-of-making-my-first-sled-out-of-uhmw-plastic/4881>\
**Category:** Sled\
**Created:** [July 15, 2018, 2:23am UTC](https://forums.maslowcnc.com/t/thinking-of-making-my-first-sled-out-of-uhmw-plastic/4881 "2018-07-15T02:23:41Z")\
**Posts on this page:** 3\
**Page:** 1

<div class="post-metadata">

**Author:** ![chewmanfoo](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/chewmanfoo/32/6139_2.png) [@chewmanfoo](https://forums.maslowcnc.com/u/chewmanfoo)\
**Post date:** [July 15, 2018, 2:23am UTC](https://forums.maslowcnc.com/t/thinking-of-making-my-first-sled-out-of-uhmw-plastic/4881/1 "2018-07-15T02:23:42Z")

</div>

I am a noob - my Maslow is still sitting in it’s box. I’m doing mental planning…

I was thinking about the sled - seems there’s some discussion about friction. I can guess that it’s bets to be in the Goldilocks zone -vis-a-vis- friction. So I’m wondering if UHMW plastic, about 3/4" thick would be a good sled surface.

Does anyone have any experience with UHMW plastic as a sled surface?

---

<div class="post-metadata">

**Author:** ![blurfl](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/blurfl/32/9_2.png) [@blurfl](https://forums.maslowcnc.com/u/blurfl)\
**Post date:** [July 15, 2018, 2:29am UTC](https://forums.maslowcnc.com/t/thinking-of-making-my-first-sled-out-of-uhmw-plastic/4881/2 "2018-07-15T02:29:52Z")

</div>

I use a piece of 1/8" thick UHMW as the sole of my 1/2" plywood sled, it works great. I think the plywood adds stiffness.

---

<div class="post-metadata">

**Author:** ![Richard\_Green](https://yyz1.discourse-cdn.com/flex031/user_avatar/forums.maslowcnc.com/richard_green/32/23316_2.png) [@Richard\_Green](https://forums.maslowcnc.com/u/Richard_Green)\
**Post date:** [July 16, 2018, 2:39pm UTC](https://forums.maslowcnc.com/t/thinking-of-making-my-first-sled-out-of-uhmw-plastic/4881/3 "2018-07-16T14:39:46Z")

</div>

I’m with you there. I paid a visit to my local cabinet shop, and talked them into gifting me with a scrap of Corian™ solid-surface countertop material. It’s 22" x 23" x 1/2", and extremely dense. I think it may be a polymer-ceramic hybrid? I’ll be making a sled from it this week. I have an idea for mounting the parts in alignment the first time:

1. Use the router baseplate as a template to drill mounting holes for the router.
2. With the router base mounted, chuck a 45deg v-groove bit in the router, and plunge the router slowly into the material just enough to make a small dimple in the sled stock.
3. dismount the router base, and use the center dimple with a compass to lay out the ring and brick mounting holes.
4. drill out the dimple into a 1/8" hole, and use it with a Jenson circle jig to cut the 18" outer circumference.
5. use a 2" holesaw to enlarge the center hole for bit and chip clearance.
6. Mount the router, ring and bricks.
7. Balance the completed sled on a chain, determine the height of the CG, and proceed to align the top bar and motor mounts accordingly.