# \#bug

**URL:** https://forums.maslowcnc.com/tag/bug/25.md

[Latest](https://forums.maslowcnc.com/latest.md) · [Categories](https://forums.maslowcnc.com/categories.md) · [Tags](https://forums.maslowcnc.com/tags.md)

---

## [Maslow stuck on - "taking slack" - solved - bug found](https://forums.maslowcnc.com/t/maslow-stuck-on-taking-slack-solved-bug-found/25632)

<div class="topic-metadata">

**Author:** [@Eldar](https://forums.maslowcnc.com/u/Eldar)\
**Replies:** 9\
**Last updated:** [March 18, 2026, 2:26pm UTC](https://forums.maslowcnc.com/t/maslow-stuck-on-taking-slack-solved-bug-found/25632 "2026-03-18T14:26:49Z")

</div>

Hi, I used M4 for quite a while now. I made my frame a bit stiffer so I had to recalibrate, I wanted a clean start so deleted maslow.yaml and index, and updated firmware to 1.19 I extend the belts, click “apply-tention…

---

## [Multiple user consistent Y axis calibration error](https://forums.maslowcnc.com/t/multiple-user-consistent-y-axis-calibration-error/25253)

<div class="topic-metadata">

**Author:** [@Eldar](https://forums.maslowcnc.com/u/Eldar)\
**Replies:** 12\
**Last updated:** [December 4, 2025, 7:06pm UTC](https://forums.maslowcnc.com/t/multiple-user-consistent-y-axis-calibration-error/25253 "2025-12-04T19:06:02Z")

</div>

Hi, I had my Maslow for a while now, it is great but I get a consistent -5% error in the Y axis (and a smaller +1% error in the X axis) I was sure it is a matter of calibration but seem that either manual or auto calib…

---

## [Duplicated input for molecule](https://forums.maslowcnc.com/t/duplicated-input-for-molecule/25126)

<div class="topic-metadata">

**Author:** [@niccokunzmann](https://forums.maslowcnc.com/u/niccokunzmann)\
**Replies:** 3\
**Last updated:** [October 31, 2025, 9:24pm UTC](https://forums.maslowcnc.com/t/duplicated-input-for-molecule/25126 "2025-10-31T21:24:28Z")

</div>

This molecule has the input length twice: The picture below should have shown the “length” input of the pipe molecule twice but I did not get the screenshot right:

---

## [Fully Adjustable Storage Dresser, Designed in FreeCAD](https://forums.maslowcnc.com/t/fully-adjustable-storage-dresser-designed-in-freecad/11906)

<div class="topic-metadata">

**Author:** [@ivxcvi](https://forums.maslowcnc.com/u/ivxcvi)\
**Replies:** 1\
**Last updated:** [December 6, 2020, 12:19am UTC](https://forums.maslowcnc.com/t/fully-adjustable-storage-dresser-designed-in-freecad/11906 "2020-12-06T00:19:20Z")

</div>

Hello, Over a majority of the last month I’ve been trying to model up a dresser for some additional storage. This project has, over this time, suffered from (blossomed into?) feature creep. It’s at this point that I …

---

## [2 bugs, or not 2 bugs, that is the question (Arduino 'insane')](https://forums.maslowcnc.com/t/2-bugs-or-not-2-bugs-that-is-the-question-arduino-insane/9105)

<div class="topic-metadata">

**Author:** [@Gero](https://forums.maslowcnc.com/u/Gero)\
**Replies:** 9\
**Last updated:** [April 26, 2019, 6:42pm UTC](https://forums.maslowcnc.com/t/2-bugs-or-not-2-bugs-that-is-the-question-arduino-insane/9105 "2019-04-26T18:42:49Z")

</div>

In my home-office fake-server Maslow setup, I managed to make the arduino ‘insane’ a couple of times. Only unplugging the arduino with closed GC will cure this state. What makes it hard to trace down is, that it’s not …

---

## [Straight line curves down at top of the sheet (solved)](https://forums.maslowcnc.com/t/straight-line-curves-down-at-top-of-the-sheet-solved/2419)

<div class="topic-metadata">

**Author:** [@Gero](https://forums.maslowcnc.com/u/Gero)\
**Replies:** 106\
**Last updated:** [April 10, 2018, 5:28pm UTC](https://forums.maslowcnc.com/t/straight-line-curves-down-at-top-of-the-sheet-solved/2419 "2018-04-10T17:28:43Z")

</div>

Any idea why a straight line at the the top would sag down, to spike up at the end? FW & GC 1.07. The gcode has a clear vertical XY coordinate to the left (cut counter-clockwise). .nc and log are in the .zip leftcut.zi…
