Human readable plan

I have set and on a surface like a floor - yes. Very well. I bought it to play with my Dog but didn’t like the sound.

Thank you

I haven’t experimented yet, but my current design (which I believe is final and will be implemented) uses three wedge shaped pieces of HDPE that are separated by 1 inch channels. This saves material and allows a means for air to the vacuum, and, since the pieces are arranged such that there is a vertical channel below the bit to allow any residual dust or chips to fall out after the vacuum is turned off.

I am also planning to use a sled made from laser cut steel or aluminum, so there’s that, but the HDPE could certainly be screwed into plywood.

1 Like

remember that you are cutting away the surface under the sled, so if you have
rings with gaps between them, there is a chance of getting hung up

if you try to float the sled (air hockey style) you run into the problem that
when you cross a section you have already cut, more air escapes and the sled
drops closer to the workpiece, throwing off your depth of cut.

1 Like

I am counting on the 1 inch gaps being thin enough to ride over most of the surface, and since the gaps don’t run fully across the sled, then there should be no problem with them dropping in a previous cut.

Pictures being worth 1000 words, here’s the best I can do without my personal laptop:
HDPE%20pattern

With the corners being rounded and the edge rounded over.

3 Likes

Are you talking about polyethylene?

Yes. High density polyethylene to be exact.

Those sled slider sections might fit well on discount or dollar store cheap cutting boards. They can be cheaper and easier to find than sheet HDPE or UHMW

2 Likes

Definitely. I decided to go with an amazon purchase instead. More expensive, but virgin material with a super slick surface (whereas many cutting boards have a texture.)

Overall, though, not a bad price for 2 square feet

I have a crude quick fix and you need a fire exrsigusher - Flame polish a cheap cutting board from the pic n dollar type store.

Thank you

Has anyone tried using a 18" aluminum pizza pan?

1 Like

Attached to the bottom of a plywood sled? I have not heard of anyone trying that.

2 Likes

I like it :grinning: That could work really well!

Your 3 piece design doesn’t take an 18x18" sheet, which really means 24 square from most sources.

Obvious in retrospect, as “they” say, but not here until you thought of it first. Great idea!

I’m not sure I want to know how to flame polish with a fire extinguisher :grinning:

1 Like

I assume you meant that it needs 18x18.

Yeah, I ended up buying 2 of the 12x24. I have plans for the extra already, so that’s fine.

1 Like

18" x 18" to cover the 17" diameter sled in one piece.

HDPE is handy stuff, rugged and easier to machine than steel. Worth keeping extra around.

I’ll take to slices with Extra Pepperoni!

Thank you

It also pairs well with a nice chianti, :slight_smile: Thin soft aluminum should be easy to cut and drill, and I have had success in the past using epoxy to bond it to wood.

2 Likes

Are you familiar with 100mph tape?

Thank you

1 Like

I just picked up a 15x20.5x.5 High Density Polyethylene for $8. I was thinking of using it to make the sled. Would it be better to split, multi piece sled (like one posted by @Keith) or simply make a 15" one?

so, three things…
one, I haven’t actually made my final sled yet, so I don’t know how well, or even if (though I am pretty confident) it will work.
two, most people have regular sleds and they seem to work great. My reasoning for making the three part HDPE sliders is really two fold: first to reduce the amount and size of HDPE I needed, and second to provide air channels for the vacuum to pull air so that it doesn’t suck the sled onto the work piece (and having the bottom channel vertical also allows for dust to fall out rather than getting packed into the central circle)
three, I am planning to use the HDPE under steel or aluminum, but the 1/2" HDPE might be rigid enough to be it’s own sled, in which case you could also route out the vacuum channels to get the benefit I am hoping for without having to make a multi part sled.

Whatever you do, be sure to post pictures! :slight_smile: