Belts will not retract

1

Green light and Red light is blinking.. Belts will not retract but it raises up and down.

Serial Messages
Index.html Version: 1.05
[MSG:INFO: Channel auto report interval set to 50 ms]
[MSG:INFO: Channel auto report interval set to 50 ms]
[MSG:INFO: FluidNC v3.0.x (noGit)]
[MSG:INFO: Compiled with ESP32 SDK:v4.4.7-dirty]
[MSG:INFO: Local filesystem type is littlefs]
[MSG:INFO: Configuration file:maslow.yaml]
[MSG:INFO: Machine Maslow S3 Board]
[MSG:INFO: Board Maslow]
[MSG:INFO: UART1 Tx:gpio.1 Rx:gpio.2 RTS:NO_PIN Baud:115200]
[MSG:INFO: SPI SCK:gpio.12 MOSI:gpio.11 MISO:gpio.13]
[MSG:INFO: SD Card cs_pin:gpio.10 detect:NO_PIN freq:8000000]
[MSG:INFO: Stepping:Timed Pulse:4us Dsbl Delay:0us Dir Delay:0us Idle Delay:240ms]
[MSG:INFO: Axis count 3]
[MSG:INFO: Axis X (-2438.400,0.000)]
[MSG:INFO: Motor0]
[MSG:INFO: Axis Y (-1219.200,0.000)]
[MSG:INFO: Motor0]
[MSG:INFO: Axis Z (-100.000,0.000)]
[MSG:INFO: Motor0]
[MSG:INFO: tmc_2209 UART1 Addr:0 Step:gpio.15 Dir:gpio.16 Disable:NO_PIN R:0.110]
[MSG:INFO: Motor1]
[MSG:INFO: tmc_2209 UART1 Addr:1 Step:gpio.46 Dir:gpio.38 Disable:NO_PIN R:0.110]
[MSG:INFO: Z Axis driver test passed]
[MSG:INFO: Z2 Axis driver test passed]
[MSG:INFO: Kinematic system: Cartesian]
[MSG:INFO: Using spindle NoSpindle]
[MSG:INFO: STA SSID is not set]
[MSG:INFO: AP SSID maslow IP 192.168.0.1 mask 255.255.255.0 channel 1]
[MSG:INFO: AP started]
[MSG:INFO: WiFi on]
[MSG:INFO: Captive Portal Started]
[MSG:INFO: HTTP started on port 80]
[MSG:INFO: Telnet started on port 23]
Retract All
[MSG:INFO: Retracting all belts]
[MSG:INFO: Requesting state change from Retracting Belts to Retracting Belts]
[MSG:INFO: Succeeded]

2

When I run test I am getting this error…

Serial Messages
Index.html Version: 1.05
[MSG:INFO: Channel auto report interval set to 50 ms]
[MSG:INFO: Caution: Unlocked]
Test
Index.html Version: 1.05
[MSG:INFO: Firmware Version: 1.05]
[MSG:INFO: I2C Timeout: ]
[MSG:INFO: 10]
[MSG:INFO: All tests passed on Top Left]
[MSG:WARN: Encoder read failure on Top Right]
[MSG:WARN: Encoder not found on Top Right]
[MSG:INFO: All tests passed on Bottom Left]
[MSG:INFO: All tests passed on Bottom Right]
[MSG:ERR: Encoder not found on Top Right]

1 Like
3

I’ve believe this is a control board problem. Anything I plug in to port CN1 gives me and encoder error.

1 Like
4

Good deduction, I think that seems right. I will DM you a code for a free replacement right now. I’d recommend getting a new encoder board and a new encoder wire too, just so that you have them in case you need them once the parts come.

You sent me an email too, right?

5

Yes I did send an email. Thanks

1 Like
6

Hey Bar, thanks the control board made it. Everything looks good with the new board!!!

1 Like